1|Page
CNMI Rigging Technician Certification Exam Practice
Questions And Correct Answers||Verified Exam!!||
(Verified Answers) Plus Rationales 2026/2027 Q&A |
Instant Download Pdf
One of the steps in a rigging planning session is to
determine the stability of the load based upon the rigging
attachment points associated with its center of gravity.
Why is this an important planning step? - Answer-You
know what the load will do in terms of movement when it is
picked up
Four essential elements in a rigging pre-job inspection:
1. Reference manufacturer information including the
weight, plant requirements and safety procedures.
2. Examine the load for structural stability, center of
gravity, and attachment points.
3. List, collect, and inspect the equipment and material
needed.
4. ? - Answer-Identify the load path
If a 1" pipe weighs 1.6 lbs per foot, then a bundle of ten 1"
pipes 20 ft long weighs: - Answer-320 lbs
,2|Page
If the center of gravity shifts during the lifting of an equally
balanced (2) pick load, the pick point nearest the cg will: -
Answer-Increase in load
If a 1" steel plate weighs 40 lbs per square foot, then a 1"
x 24" x 3' steel plate weighs: - Answer-240 lbs
Calculate the weight of an open box steel box that is made
of 1" plate measuring 5' long by 4' wide by 3' high that is
filled with sand. - Answer-10,160 lbs
Calculate to the nearest pound the weight of a steel tank
that is made up of 1/2" plate measuring 4' long by 4' wide
by 2' high that contains 50 gallons of diesel fuel. - Answer-
1630 lbs
Which of the following is unacceptable for determining
load weight? - Answer-Lift load and determine stress/strain
on slings
Where should the CG of a load be located during a lift? -
Answer-Below the attachment points
, 3|Page
Calculate the weight to the nearest pound the weight of a
steel tank that is made of 1/2" plate measuring 4' long by
4' wide by 2' tall that contains 75 gallons of diesel fuel. -
Answer-1805 lbs
Which reference should be the final authority in
determining rigging specifications on a piece of
equipment? - Answer-Vendor Technical Manual
Rigging specifications for a specific piece of equipment
may be found in: - Answer-Vendor Technical Manual
If the equipment you are working on has a written
procedure for performing a lift and you find it differs from
the manufacturers specifications for lifting, you should: -
Answer-Stop the job, get clarification, and a procedure
change
If a two leg sling attachment is used to lift a long load of
flexible material, the load may: - Answer-Buckle in the
middle
CNMI Rigging Technician Certification Exam Practice
Questions And Correct Answers||Verified Exam!!||
(Verified Answers) Plus Rationales 2026/2027 Q&A |
Instant Download Pdf
One of the steps in a rigging planning session is to
determine the stability of the load based upon the rigging
attachment points associated with its center of gravity.
Why is this an important planning step? - Answer-You
know what the load will do in terms of movement when it is
picked up
Four essential elements in a rigging pre-job inspection:
1. Reference manufacturer information including the
weight, plant requirements and safety procedures.
2. Examine the load for structural stability, center of
gravity, and attachment points.
3. List, collect, and inspect the equipment and material
needed.
4. ? - Answer-Identify the load path
If a 1" pipe weighs 1.6 lbs per foot, then a bundle of ten 1"
pipes 20 ft long weighs: - Answer-320 lbs
,2|Page
If the center of gravity shifts during the lifting of an equally
balanced (2) pick load, the pick point nearest the cg will: -
Answer-Increase in load
If a 1" steel plate weighs 40 lbs per square foot, then a 1"
x 24" x 3' steel plate weighs: - Answer-240 lbs
Calculate the weight of an open box steel box that is made
of 1" plate measuring 5' long by 4' wide by 3' high that is
filled with sand. - Answer-10,160 lbs
Calculate to the nearest pound the weight of a steel tank
that is made up of 1/2" plate measuring 4' long by 4' wide
by 2' high that contains 50 gallons of diesel fuel. - Answer-
1630 lbs
Which of the following is unacceptable for determining
load weight? - Answer-Lift load and determine stress/strain
on slings
Where should the CG of a load be located during a lift? -
Answer-Below the attachment points
, 3|Page
Calculate the weight to the nearest pound the weight of a
steel tank that is made of 1/2" plate measuring 4' long by
4' wide by 2' tall that contains 75 gallons of diesel fuel. -
Answer-1805 lbs
Which reference should be the final authority in
determining rigging specifications on a piece of
equipment? - Answer-Vendor Technical Manual
Rigging specifications for a specific piece of equipment
may be found in: - Answer-Vendor Technical Manual
If the equipment you are working on has a written
procedure for performing a lift and you find it differs from
the manufacturers specifications for lifting, you should: -
Answer-Stop the job, get clarification, and a procedure
change
If a two leg sling attachment is used to lift a long load of
flexible material, the load may: - Answer-Buckle in the
middle
