ASE MLR Practice QUESTIONS AND ANSWERS |
LATEST UPDATE
Save
Terms in this set (59)
Technician observes that the brake Both A and B
fluid level is at the "Min" mark in the
master cylinder reservoir. Tech A says
that worn front pads could be the
cause. Tech B says that a leak in the
brake hydraulic system could be the
cause. Who is right?
The tires of a vehicle are being A only
rotated and balanced. Tech A says
that the wheel weight retaining clips
must be matched to the rim profile.
Tech B says that directional tires are
rotated in a criss-cross pattern. Who
is right?
A vehicle's halogen headlamp bulbs B only
are being replaced. Technician A says
the glass part of the bulb can only
be handled with bare hands.
Technician B says the headlamp may
need to be removed. Who is right?
, On a Metric Micrometer upper 5.51mm
sleeve reading 5.0mm with lower
sleeve reading 0.50mm and a thimble
reading of 0.01mm what is the overall
reading?
The fuel filter on a fuel-injected A only
vehicle is being replaced. Tech A
says the fuel pressure should be
relieved before removing the filter.
Tech B says that the arrow on the fuel
filter should point towards the fuel
tank. Who is right?
Which of these is an indication of air The brake pedal feels low and spongy
in the brake hydraulic system?
A grabbing brake condition can be Fluid contaminated brake linings
caused by any of these EXCEPT:
While inspecting the rear axle wheel Tech B
studs on a rear-wheel drive vehicle,
the technician observed that one Explanation:
stud is damaged. Technician A says The thread pitch and diameter of the replacement
that all the wheel studs on the hub stud must match the original to ensure proper
assembly should be replaced. fitting. Replacing all studs is not always necessary
Technician B says that the thread unless advised by the manufacturer or if other studs
pitch and diameter of the are also compromised.
replacement stud must be the same
as the original. Who is right?
LATEST UPDATE
Save
Terms in this set (59)
Technician observes that the brake Both A and B
fluid level is at the "Min" mark in the
master cylinder reservoir. Tech A says
that worn front pads could be the
cause. Tech B says that a leak in the
brake hydraulic system could be the
cause. Who is right?
The tires of a vehicle are being A only
rotated and balanced. Tech A says
that the wheel weight retaining clips
must be matched to the rim profile.
Tech B says that directional tires are
rotated in a criss-cross pattern. Who
is right?
A vehicle's halogen headlamp bulbs B only
are being replaced. Technician A says
the glass part of the bulb can only
be handled with bare hands.
Technician B says the headlamp may
need to be removed. Who is right?
, On a Metric Micrometer upper 5.51mm
sleeve reading 5.0mm with lower
sleeve reading 0.50mm and a thimble
reading of 0.01mm what is the overall
reading?
The fuel filter on a fuel-injected A only
vehicle is being replaced. Tech A
says the fuel pressure should be
relieved before removing the filter.
Tech B says that the arrow on the fuel
filter should point towards the fuel
tank. Who is right?
Which of these is an indication of air The brake pedal feels low and spongy
in the brake hydraulic system?
A grabbing brake condition can be Fluid contaminated brake linings
caused by any of these EXCEPT:
While inspecting the rear axle wheel Tech B
studs on a rear-wheel drive vehicle,
the technician observed that one Explanation:
stud is damaged. Technician A says The thread pitch and diameter of the replacement
that all the wheel studs on the hub stud must match the original to ensure proper
assembly should be replaced. fitting. Replacing all studs is not always necessary
Technician B says that the thread unless advised by the manufacturer or if other studs
pitch and diameter of the are also compromised.
replacement stud must be the same
as the original. Who is right?
