powerplant written questions and answers |
verified
Save
Terms in this set (76)
AM.III.A.K2 In what piston should the cylinder 1 should be set to fire 30 degrees before
crankshaft be when a magneto is top dead center (depends on the engine)
being timed to the engine
AM.III.A.K2 What is checked on Idling rpm, and manifold pressure, engine
engine runup to determine the acceleration, maximum static rpm and manifold
operational condition of the engine pressure, magneto drop, ignition switch safety
check, prop pitch change, prop feathering, oil
pressure, fuel pressure and fuel flow
AM.III.A.K8 What must be inspected The prop, Lubrication system, ignition system, fuel
to determine the airworthiness of an metering system, cooling system, and the exhaust
engine installation system
AM.III.A.K8 Where can you find the TCDS
correct grade of fuel and the amount
of engine lubricating oil for an
aircraft engine
AM.III.A.K8 What are the basic steps A. know how the system should operate
in troubleshooting an engine B. observe how the system is operating
installation C. Divide the system into smaller parts to find the
trouble
D. look for the obvious problems first
, AM.III.A.K8 Where do you find In the maintenance manual
instructions for removing an engine
from an aircraft
AM.III.A.K8 What must normally be The tail of the airplane must be supported
done to a nose wheel airplane
before removing an engine
AM.III.A.K8 What should be used to The correct plugs or caps. never cover the end of a
cover the ends of fuel and oil lines line with tape
that have been disconnected from
the engine
AM.III.A.K8 What is meant by a QEC an engine that has been prepared for quick engine
engine assembly change, the engine is on its mount and all the
accessories are installed. a minimum of time is
required to change the engines. all that is needed
for the controls wiring and fluid lines to be
connected to the firewall
AM.III.A.K8 What is meant by rigging The control on the engine must hit its stop before
the engine controls so they have the handle in the cockpit/ also known as spring
cushion back
AM.III.A.K8 what are two ways of pre A. before the spark plugs are installed, and after
oiling an engine the oil tank or sump is filled, turn the engine over
with the starter until oil runs out of the fitting to
which the oil pressure gauge connects
B use a pre oiler tank, air pressure forces oil through
all of the passages until some of it flows from the oil
pressure gauge fitting
verified
Save
Terms in this set (76)
AM.III.A.K2 In what piston should the cylinder 1 should be set to fire 30 degrees before
crankshaft be when a magneto is top dead center (depends on the engine)
being timed to the engine
AM.III.A.K2 What is checked on Idling rpm, and manifold pressure, engine
engine runup to determine the acceleration, maximum static rpm and manifold
operational condition of the engine pressure, magneto drop, ignition switch safety
check, prop pitch change, prop feathering, oil
pressure, fuel pressure and fuel flow
AM.III.A.K8 What must be inspected The prop, Lubrication system, ignition system, fuel
to determine the airworthiness of an metering system, cooling system, and the exhaust
engine installation system
AM.III.A.K8 Where can you find the TCDS
correct grade of fuel and the amount
of engine lubricating oil for an
aircraft engine
AM.III.A.K8 What are the basic steps A. know how the system should operate
in troubleshooting an engine B. observe how the system is operating
installation C. Divide the system into smaller parts to find the
trouble
D. look for the obvious problems first
, AM.III.A.K8 Where do you find In the maintenance manual
instructions for removing an engine
from an aircraft
AM.III.A.K8 What must normally be The tail of the airplane must be supported
done to a nose wheel airplane
before removing an engine
AM.III.A.K8 What should be used to The correct plugs or caps. never cover the end of a
cover the ends of fuel and oil lines line with tape
that have been disconnected from
the engine
AM.III.A.K8 What is meant by a QEC an engine that has been prepared for quick engine
engine assembly change, the engine is on its mount and all the
accessories are installed. a minimum of time is
required to change the engines. all that is needed
for the controls wiring and fluid lines to be
connected to the firewall
AM.III.A.K8 What is meant by rigging The control on the engine must hit its stop before
the engine controls so they have the handle in the cockpit/ also known as spring
cushion back
AM.III.A.K8 what are two ways of pre A. before the spark plugs are installed, and after
oiling an engine the oil tank or sump is filled, turn the engine over
with the starter until oil runs out of the fitting to
which the oil pressure gauge connects
B use a pre oiler tank, air pressure forces oil through
all of the passages until some of it flows from the oil
pressure gauge fitting
