Page 1 of 118
NFPA 70B Electrical Equipment Maintenance Exam
COMPLETE QUESTIONS AND DETAILED SOLUTIONS
LATEST UPDATE THIS YEAR-JUST RELEASED
NFPA 70B Electrical Equipment Maintenance Exam — Point Form Coverage
• NFPA 70B purpose and scope (electrical maintenance best practices)
• Electrical equipment maintenance program (EEMP) structure
• Preventive maintenance vs predictive maintenance vs condition-based maintenance
• Reliability-centered maintenance principles
• Risk-based maintenance planning
• Equipment life-cycle management
• Electrical safety principles (aligned with NFPA 70E)
• Arc flash hazards and PPE requirements
• Shock protection boundaries
• Lockout/tagout (LOTO) procedures
• Energized work restrictions and safety rules
• Maintenance scheduling and inspection intervals
• Critical vs non-critical equipment prioritization
• Manufacturer maintenance recommendations
• Maintenance documentation requirements
• Switchgear inspection and maintenance
• Circuit breaker testing and servicing
• Panelboards and distribution panels
• Busbar inspection and connection integrity
• Disconnect switch maintenance
• Transformer maintenance (dry-type and oil-filled)
• Insulation resistance testing
• Oil sampling and dielectric testing
• Cooling system monitoring
• Overheating prevention
• Motor maintenance and testing
• Bearing lubrication and inspection
• Vibration and alignment checks
• Motor insulation testing (megger)
• Variable Frequency Drive (VFD) maintenance
• Cable and wiring system maintenance
• Insulation degradation checks
• Termination torque and connection tightening
• Grounding and bonding inspection
• Conduit and cable tray condition
• Predictive maintenance techniques
• Infrared thermography (hot spot detection)
• Vibration analysis
• Ultrasound testing
• Partial discharge testing
, Page 2 of 118
• Oil and gas analysis (DGA)
• Preventive maintenance tasks
• Cleaning and tightening electrical connections
• Lubrication of mechanical parts
• Replacement of worn components
• Calibration of protective devices
• Electrical testing methods
• Insulation resistance testing (megger)
• Continuity testing
• Ground resistance testing
• Power quality monitoring
• Load testing
• Emergency power systems maintenance
• Generator inspection and servicing
• Automatic transfer switch (ATS) testing
• Battery backup systems maintenance
• Fuel system checks
• Arc flash prevention and mitigation
• Fault current awareness
• Equipment labeling requirements
• Maintenance role in arc flash reduction
• Equipment failure prevention
• Overheating detection
• Corrosion and contamination control
• Early failure warning signs
• Maintenance documentation and reporting
• Equipment history tracking
• Maintenance logs and reports
• Defect reporting and corrective actions
• Compliance documentation
• Scenario-based applications
• Diagnosing electrical faults
• Selecting maintenance methods
• Identifying failing equipment conditions
• Choosing repair vs replacement decisions
NFPA 70B Exam — MCQ Practice Set 1 (1–50)
, Page 3 of 118
1. What is the primary purpose of NFPA 70B?
A. Electrical installation code enforcement
B. Electrical equipment maintenance best practices guidance
C. Fire sprinkler design standards
D. Building structural safety rules
Answer: B
Rationale: NFPA 70B provides recommended practices for electrical equipment maintenance to improve
safety, reliability, and system performance.
2. What is the main goal of an Electrical Equipment Maintenance Program (EEMP)?
A. Reduce electrical system voltage
B. Ensure equipment reliability and safety through structured maintenance
C. Increase arc flash risk
D. Eliminate inspections
, Page 4 of 118
Answer: B
Rationale: An EEMP ensures systematic maintenance to improve equipment reliability and reduce
failure risk.
3. Preventive maintenance is best described as:
A. Repair after failure
B. Maintenance performed on a fixed schedule
C. Maintenance based only on real-time sensors
D. No maintenance required
Answer: B
Rationale: Preventive maintenance is time-based and performed regularly to prevent failures.
4. Predictive maintenance primarily relies on:
A. Random inspections
B. Equipment condition monitoring and trend analysis
NFPA 70B Electrical Equipment Maintenance Exam
COMPLETE QUESTIONS AND DETAILED SOLUTIONS
LATEST UPDATE THIS YEAR-JUST RELEASED
NFPA 70B Electrical Equipment Maintenance Exam — Point Form Coverage
• NFPA 70B purpose and scope (electrical maintenance best practices)
• Electrical equipment maintenance program (EEMP) structure
• Preventive maintenance vs predictive maintenance vs condition-based maintenance
• Reliability-centered maintenance principles
• Risk-based maintenance planning
• Equipment life-cycle management
• Electrical safety principles (aligned with NFPA 70E)
• Arc flash hazards and PPE requirements
• Shock protection boundaries
• Lockout/tagout (LOTO) procedures
• Energized work restrictions and safety rules
• Maintenance scheduling and inspection intervals
• Critical vs non-critical equipment prioritization
• Manufacturer maintenance recommendations
• Maintenance documentation requirements
• Switchgear inspection and maintenance
• Circuit breaker testing and servicing
• Panelboards and distribution panels
• Busbar inspection and connection integrity
• Disconnect switch maintenance
• Transformer maintenance (dry-type and oil-filled)
• Insulation resistance testing
• Oil sampling and dielectric testing
• Cooling system monitoring
• Overheating prevention
• Motor maintenance and testing
• Bearing lubrication and inspection
• Vibration and alignment checks
• Motor insulation testing (megger)
• Variable Frequency Drive (VFD) maintenance
• Cable and wiring system maintenance
• Insulation degradation checks
• Termination torque and connection tightening
• Grounding and bonding inspection
• Conduit and cable tray condition
• Predictive maintenance techniques
• Infrared thermography (hot spot detection)
• Vibration analysis
• Ultrasound testing
• Partial discharge testing
, Page 2 of 118
• Oil and gas analysis (DGA)
• Preventive maintenance tasks
• Cleaning and tightening electrical connections
• Lubrication of mechanical parts
• Replacement of worn components
• Calibration of protective devices
• Electrical testing methods
• Insulation resistance testing (megger)
• Continuity testing
• Ground resistance testing
• Power quality monitoring
• Load testing
• Emergency power systems maintenance
• Generator inspection and servicing
• Automatic transfer switch (ATS) testing
• Battery backup systems maintenance
• Fuel system checks
• Arc flash prevention and mitigation
• Fault current awareness
• Equipment labeling requirements
• Maintenance role in arc flash reduction
• Equipment failure prevention
• Overheating detection
• Corrosion and contamination control
• Early failure warning signs
• Maintenance documentation and reporting
• Equipment history tracking
• Maintenance logs and reports
• Defect reporting and corrective actions
• Compliance documentation
• Scenario-based applications
• Diagnosing electrical faults
• Selecting maintenance methods
• Identifying failing equipment conditions
• Choosing repair vs replacement decisions
NFPA 70B Exam — MCQ Practice Set 1 (1–50)
, Page 3 of 118
1. What is the primary purpose of NFPA 70B?
A. Electrical installation code enforcement
B. Electrical equipment maintenance best practices guidance
C. Fire sprinkler design standards
D. Building structural safety rules
Answer: B
Rationale: NFPA 70B provides recommended practices for electrical equipment maintenance to improve
safety, reliability, and system performance.
2. What is the main goal of an Electrical Equipment Maintenance Program (EEMP)?
A. Reduce electrical system voltage
B. Ensure equipment reliability and safety through structured maintenance
C. Increase arc flash risk
D. Eliminate inspections
, Page 4 of 118
Answer: B
Rationale: An EEMP ensures systematic maintenance to improve equipment reliability and reduce
failure risk.
3. Preventive maintenance is best described as:
A. Repair after failure
B. Maintenance performed on a fixed schedule
C. Maintenance based only on real-time sensors
D. No maintenance required
Answer: B
Rationale: Preventive maintenance is time-based and performed regularly to prevent failures.
4. Predictive maintenance primarily relies on:
A. Random inspections
B. Equipment condition monitoring and trend analysis
