Arresting Gear Engine Exam Questions &
Answers (Grade A+)
What is the capacity of the f without saltwater coolers -
correct answer ✅380
What is the two block runout -
correct answer ✅195
What is the x-head stop for a new purchase cable -
correct answer ✅1-6 1/2
What is x-head stop for a used purchase cable -
correct answer ✅1-6
What is your anchor damper stroke -
correct answer ✅15ft 8inches
What does HPCA stand for -
correct answer ✅Hydraulic power and control system
What does RCV stand for -
correct answer ✅Retract control valve
,Arresting Gear Engine Exam Questions &
Answers (Grade A+)
What does RCI stand for -
correct answer ✅Retract control indicator
What does ARC stand for -
correct answer ✅Advance recovery control system
After how many arrestment would you perform the R-10 crosshead
rail -
correct answer ✅After every 1000 arrestment
After how many arrestments do you Perform the R-12 Anchor
Damper -
correct answer ✅1000 traps
Maximum allowable clearance for anchor damper slippers are -
correct answer ✅.030
How many slippers are on the floating piston -
correct answer ✅24 slippers
What is the pressure of the saltwater cooler water pressure -
correct answer ✅200gpms
,Arresting Gear Engine Exam Questions &
Answers (Grade A+)
What kind of valve is in the RCV -
correct answer ✅Self contained poppet valve
How many ports are in the RCV and what are they -
correct answer ✅3
Mec
Accumulator
Anchor damper
How often do you replace the synchronous belts regardless off
condition -
correct answer ✅Every 36 months
What is the MRC for pre-op -
correct answer ✅R-1
In no particular order what are some steps for pre-op -
correct answer ✅Establish comms
Charge accumulator to 400 psi
Auxiliary 2500-3000
, Arresting Gear Engine Exam Questions &
Answers (Grade A+)
Turn power on
Turn CB1,2,3 on
Make sure no 3 fuses are lit on FSIB
Ensure failsafe pressures are between 2525-2950
Vent overbalance chamber and dash pot
Verify RCV opens and unlocks
Actuator test
X-head to stop (no more than 1/2 inch)
Verify mec shutoff (transducers) valve is open
Inspect tracks and ram for fod
Auto lube pressure 80+-5
*Target position
1.6inches with a motion rate of 0.1 inches a sec
*Decrease target position 0.1 inches sign a motion rate of 1.0inches
per second
Offline test
Make sure it reads 0.9-1.1
Answers (Grade A+)
What is the capacity of the f without saltwater coolers -
correct answer ✅380
What is the two block runout -
correct answer ✅195
What is the x-head stop for a new purchase cable -
correct answer ✅1-6 1/2
What is x-head stop for a used purchase cable -
correct answer ✅1-6
What is your anchor damper stroke -
correct answer ✅15ft 8inches
What does HPCA stand for -
correct answer ✅Hydraulic power and control system
What does RCV stand for -
correct answer ✅Retract control valve
,Arresting Gear Engine Exam Questions &
Answers (Grade A+)
What does RCI stand for -
correct answer ✅Retract control indicator
What does ARC stand for -
correct answer ✅Advance recovery control system
After how many arrestment would you perform the R-10 crosshead
rail -
correct answer ✅After every 1000 arrestment
After how many arrestments do you Perform the R-12 Anchor
Damper -
correct answer ✅1000 traps
Maximum allowable clearance for anchor damper slippers are -
correct answer ✅.030
How many slippers are on the floating piston -
correct answer ✅24 slippers
What is the pressure of the saltwater cooler water pressure -
correct answer ✅200gpms
,Arresting Gear Engine Exam Questions &
Answers (Grade A+)
What kind of valve is in the RCV -
correct answer ✅Self contained poppet valve
How many ports are in the RCV and what are they -
correct answer ✅3
Mec
Accumulator
Anchor damper
How often do you replace the synchronous belts regardless off
condition -
correct answer ✅Every 36 months
What is the MRC for pre-op -
correct answer ✅R-1
In no particular order what are some steps for pre-op -
correct answer ✅Establish comms
Charge accumulator to 400 psi
Auxiliary 2500-3000
, Arresting Gear Engine Exam Questions &
Answers (Grade A+)
Turn power on
Turn CB1,2,3 on
Make sure no 3 fuses are lit on FSIB
Ensure failsafe pressures are between 2525-2950
Vent overbalance chamber and dash pot
Verify RCV opens and unlocks
Actuator test
X-head to stop (no more than 1/2 inch)
Verify mec shutoff (transducers) valve is open
Inspect tracks and ram for fod
Auto lube pressure 80+-5
*Target position
1.6inches with a motion rate of 0.1 inches a sec
*Decrease target position 0.1 inches sign a motion rate of 1.0inches
per second
Offline test
Make sure it reads 0.9-1.1
