FDNY P98 ELITE EXIT EXAM PREP – 100% ACCURACY & SUCCESS GUARANTEETHE MASTER KEY: FULL EXAM REPOSITORY & DETAILED SOLUTIONS

Fuel-oil is primarily used in buildings for: A. Cooling systems B. Generators and heating C. Water supply D. Lighting only Correct Answer: B Rationale: Fuel-oil is commonly used to power emergency generators and building heating systems. 2. The P-98 Certificate of Fitness is required for: A. Electrical wiring B. Supervising fuel-oil transfer C. Plumbing repair D. Fire alarm installation Correct Answer: B Rationale: P-98 COF holders are responsible for supervising fuel-oil transfer systems. 3. “General supervision” refers to: A. No supervision required B. Oversight by P-98 certificate holder C. Fire department only D. Building owner only Correct Answer: B Rationale: General supervision is provided by the certified P-98 operator. 4. “Personal supervision” means: A. Remote monitoring B. Direct oversight during inspection/testing C. No supervision D. Automatic control only Correct Answer: B Rationale: Personal supervision requires physical presence during critical tasks. 5. Fuel-oil tanks and piping must be inspected: A. Monthly B. Yearly C. Weekly D. Every 5 years Correct Answer: C Rationale: Weekly inspections ensure leak prevention and system safety. 6. Float switches must be tested: A. Daily B. Weekly C. Monthly D. Never Correct Answer: B Rationale: Float switches are safety devices and must be tested weekly. 7. The Certificate of Compliance is issued by: A. FDNY only B. NYCDOB C. EPA D. OSHA Correct Answer: B Rationale: NYC Department of Buildings issues Certificates of Compliance. 8. NYCDEP requirements refer to: A. Electrical safety B. Air pollution control code C. Plumbing standards D. Building painting rules Correct Answer: B Rationale: NYCDEP regulates air pollution from fuel systems. 9. Fuel-oil permit is issued by: A. FDNY B. NYPD C. EPA D. DOB Correct Answer: A Rationale: FDNY regulates storage and use permits for fuel-oil. 10. The suction pump function is to: A. Cool the oil B. Circulate oil in the system C. Burn oil D. Filter air Correct Answer: B Rationale: The suction pump moves oil through the piping system. 11. The oil filter is used to: A. Increase pressure B. Remove contaminants C. Heat oil D. Store oil Correct Answer: B Rationale: Filters remove dirt and sediment before combustion. 12. The suction line must be placed: A. At tank bottom B. 6 inches above tank bottom C. Above burner D. Inside chimney Correct Answer: B Rationale: Prevents sediment from being drawn into the system. 13. A vacuum gauge measures: A. Temperature B. Pressure below atmospheric pressure C. Fuel quantity D. Electrical current Correct Answer: B Rationale: It detects suction line performance and blockage. 14. Excessive vacuum readings indicate: A. Normal operation B. Line obstruction C. High fuel quality D. Low combustion Correct Answer: B Rationale: Usually caused by clogged filters or blocked suction lines. 15. The shut-off valve is used to: A. Increase fuel flow B. Stop oil flow for maintenance C. Heat oil D. Mix air Correct Answer: B Rationale: Used during maintenance or emergency shutdown. 16. The main fuel valve controls: A. Water flow B. Oil flow to atomizer C. Air pressure D. Steam output Correct Answer: B Rationale: It regulates oil delivery to the burner atomizer. 17. Diked areas are used to: A. Heat oil B. Contain oil leaks C. Burn fuel D. Increase pressure Correct Answer: B Rationale: Dikes prevent spilled oil from spreading. 18. #2 fuel-oil is described as: A. Thick and heavy B. Thin and light C. Solid D. Gas only Correct Answer: B Rationale: It is commonly used for combustion systems and easy to pump. 19. Oil burners are used to: A. Store fuel B. Burn fuel for heat C. Pump water D. Filter air Correct Answer: B Rationale: Oil burners convert fuel into heat energy. 20. Ignition failure causes: A. Increased heat B. Burner shutdown C. More air flow D. Fuel storage Correct Answer: B Rationale: Safety systems shut down burners if ignition fails. 21. Combustion is: A. Cooling process B. Chemical reaction producing heat C. Mechanical movement D. Electrical discharge Correct Answer: B Rationale: Combustion is the reaction of oxygen with fuel producing heat. 22. Primary air in combustion is: A. Air after flame B. Air mixed before nozzle C. Exhaust air D. Cooling air Correct Answer: B Rationale: Primary air mixes with fuel before leaving the nozzle.