NCCCO CORE UPDATED ACTUAL EXAMS QUESTIONS
AND ANSWERS SURE A+
✔✔Cantelever Boom Sections Must? - ✔✔Not exceed mfg limitations and instructions
for boom lengths.
✔✔Order Of Boom Section Assembly is? - ✔✔Short to Long, unless mfg recommends
otherwise.
✔✔Use Dog (Pawl)? - ✔✔When Assembling.
✔✔OSHA 29 CFR 1926.1408 Covers? - ✔✔Power Lines. Voltages Under 350kv.
✔✔Per OSHA 1926.1408 (Table A) Minimum Line Clearance Distances While
Stationary Are? - ✔✔0-50kv / 10'
50-200kv / 15'
200-350kv / 20'
350-500kv / 25'
500-750kv / 35'
750-1000kv / 45'
"OVER 1000KV UTILITY/REGISTERED PROFESSIONAL ENGINEER, who is
qualified, WILL ESTABLISH SAFE DISTANCES"
, ✔✔Per OSHA 1926.1411 (Table T)
Minimum Line Clearance Distances While Traveling Are? - ✔✔<0.75kv / 4'
0.75-50kv / 6'
50kv-345kv / 10'
345kv-750kv / 16'
750kv-1000kv / 20'
"Over 1000kv, utility/ registered professional engineer, who is qualified, dictates
allowable distances."
✔✔Per OSHA 1926.1407-1411
While Traveling, Or stationary,
A Dedicated Spotter is Required? - ✔✔When any part of Crane will come closer than
20' of energized conducter, Any Voltage Under 1000kv.
✔✔Per OSHA 1926.1410
An Insulating link/device must be installed where? - ✔✔Between end of load line, (or
below), and the load.
✔✔Per OSHA 1926.1407-1411
When using a tagline around energized lines it must be? - ✔✔Non-conductive,
(Polypropylene)
✔✔Employer must _____ to the Operators and Crew Members Assigned to Work
around Energized Conductors. - ✔✔Train and Explain Dangers and Hazards
✔✔Per OSHA 1926.1401
A Qualified Person Is? - ✔✔By possession of a degree, certificate, professional
standing, or by extensive knowledge, training and experience successfully
demonstrates the ability to resolve/solve problems related to the subject matter, work, or
the project.
✔✔Per OSHA 1926.1401
A qualified Rigger is? - ✔✔A rigger who meets the qualified persons criteria.
✔✔Per OSHA 1926.1401
AND ANSWERS SURE A+
✔✔Cantelever Boom Sections Must? - ✔✔Not exceed mfg limitations and instructions
for boom lengths.
✔✔Order Of Boom Section Assembly is? - ✔✔Short to Long, unless mfg recommends
otherwise.
✔✔Use Dog (Pawl)? - ✔✔When Assembling.
✔✔OSHA 29 CFR 1926.1408 Covers? - ✔✔Power Lines. Voltages Under 350kv.
✔✔Per OSHA 1926.1408 (Table A) Minimum Line Clearance Distances While
Stationary Are? - ✔✔0-50kv / 10'
50-200kv / 15'
200-350kv / 20'
350-500kv / 25'
500-750kv / 35'
750-1000kv / 45'
"OVER 1000KV UTILITY/REGISTERED PROFESSIONAL ENGINEER, who is
qualified, WILL ESTABLISH SAFE DISTANCES"
, ✔✔Per OSHA 1926.1411 (Table T)
Minimum Line Clearance Distances While Traveling Are? - ✔✔<0.75kv / 4'
0.75-50kv / 6'
50kv-345kv / 10'
345kv-750kv / 16'
750kv-1000kv / 20'
"Over 1000kv, utility/ registered professional engineer, who is qualified, dictates
allowable distances."
✔✔Per OSHA 1926.1407-1411
While Traveling, Or stationary,
A Dedicated Spotter is Required? - ✔✔When any part of Crane will come closer than
20' of energized conducter, Any Voltage Under 1000kv.
✔✔Per OSHA 1926.1410
An Insulating link/device must be installed where? - ✔✔Between end of load line, (or
below), and the load.
✔✔Per OSHA 1926.1407-1411
When using a tagline around energized lines it must be? - ✔✔Non-conductive,
(Polypropylene)
✔✔Employer must _____ to the Operators and Crew Members Assigned to Work
around Energized Conductors. - ✔✔Train and Explain Dangers and Hazards
✔✔Per OSHA 1926.1401
A Qualified Person Is? - ✔✔By possession of a degree, certificate, professional
standing, or by extensive knowledge, training and experience successfully
demonstrates the ability to resolve/solve problems related to the subject matter, work, or
the project.
✔✔Per OSHA 1926.1401
A qualified Rigger is? - ✔✔A rigger who meets the qualified persons criteria.
✔✔Per OSHA 1926.1401
