MANUAL TRANSMISSION/TRANSAXLE PRINCIPLES
NEWEST FINAL Updated Exam 2026 WITH Recent Newest
Verified And Well Analyzed Exam Questions (Actual Exam
2026-2027) Correct Detailed & Verified ANSWERS (100%
Accurate Solutions) ALREADY GRADED A+||NEWEST
VERSION Of The Exam Guarantee Pass!!
clutch system - ANSWERS-a mechanically operated assembly that connects and
disconnects the engine from the transmission
cv joints - ANSWERS-joints commonly used in front wheel drive vehicles to allow
flexibility of the axle wheel turning
dead axle - ANSWERS-an axle that supplies no power to the wheels
differential gears - ANSWERS-gears situated in the final drive assembly that are
meshed together with both axles, allowing the wheels to rotate at different speeds when
turning a corner
`accelerator pedal - ANSWERS-The foot-operated pedal used by the driver to
increase and decrease the amount of power the engine develops.
axial load - ANSWERS-the load applied in line with a shaft. it can be controlled with
thrust bearings
clutch pedal - ANSWERS-the foot operated peddle driver to engage and disengage the
clutch
clutch safety switch - ANSWERS-an electrical switch that is operated by the clutch
pedal and keeps the starter motor from cranking the engine over until the clutch is fully
depressed
, drive axle assembly - ANSWERS-the components that make up the drive axle including
the axles ,final drive assembly ,bearings and axle housing
drive axle - ANSWERS-an axle that provides power to a wheel
drive shaft - ANSWERS-the hollow tube with flexible joints on each end that transmits
power from the transmission to the final drive unit
final drive assembly - ANSWERS-an assembly used to power the drive wheels and
allow the wheels to rotate at different speeds as the vehicle turns
gear ratio - ANSWERS-the description of the difference in speed between gears in
mesh, determined by comparing the number of teeth on each gear. For example a gear
set that has a drive gear with 5 teeth in mesh with a driven gear of 25 teeth has a gear
ratio of 5:1
gear set - ANSWERS-two or more gears that are in mesh with eachother
gear synchronizer - ANSWERS-an assembly in the transmission that is used to bring 2
unequally spinning shafts or gears to the same speed when upshifting or down shifting
gear - ANSWERS-a relatively round, rotating part with internal or external teeth that are
designed to mesh with another gear for the purpose of transmitting torque
half shaft - ANSWERS-an axle that has cv joints on each end and that fits between the
trans axle and wheel. typically one is used on each side of the vehicle
helical gears - ANSWERS-gears that have teeth set on angle to the gear face they
operate more quietly than spur gears
NEWEST FINAL Updated Exam 2026 WITH Recent Newest
Verified And Well Analyzed Exam Questions (Actual Exam
2026-2027) Correct Detailed & Verified ANSWERS (100%
Accurate Solutions) ALREADY GRADED A+||NEWEST
VERSION Of The Exam Guarantee Pass!!
clutch system - ANSWERS-a mechanically operated assembly that connects and
disconnects the engine from the transmission
cv joints - ANSWERS-joints commonly used in front wheel drive vehicles to allow
flexibility of the axle wheel turning
dead axle - ANSWERS-an axle that supplies no power to the wheels
differential gears - ANSWERS-gears situated in the final drive assembly that are
meshed together with both axles, allowing the wheels to rotate at different speeds when
turning a corner
`accelerator pedal - ANSWERS-The foot-operated pedal used by the driver to
increase and decrease the amount of power the engine develops.
axial load - ANSWERS-the load applied in line with a shaft. it can be controlled with
thrust bearings
clutch pedal - ANSWERS-the foot operated peddle driver to engage and disengage the
clutch
clutch safety switch - ANSWERS-an electrical switch that is operated by the clutch
pedal and keeps the starter motor from cranking the engine over until the clutch is fully
depressed
, drive axle assembly - ANSWERS-the components that make up the drive axle including
the axles ,final drive assembly ,bearings and axle housing
drive axle - ANSWERS-an axle that provides power to a wheel
drive shaft - ANSWERS-the hollow tube with flexible joints on each end that transmits
power from the transmission to the final drive unit
final drive assembly - ANSWERS-an assembly used to power the drive wheels and
allow the wheels to rotate at different speeds as the vehicle turns
gear ratio - ANSWERS-the description of the difference in speed between gears in
mesh, determined by comparing the number of teeth on each gear. For example a gear
set that has a drive gear with 5 teeth in mesh with a driven gear of 25 teeth has a gear
ratio of 5:1
gear set - ANSWERS-two or more gears that are in mesh with eachother
gear synchronizer - ANSWERS-an assembly in the transmission that is used to bring 2
unequally spinning shafts or gears to the same speed when upshifting or down shifting
gear - ANSWERS-a relatively round, rotating part with internal or external teeth that are
designed to mesh with another gear for the purpose of transmitting torque
half shaft - ANSWERS-an axle that has cv joints on each end and that fits between the
trans axle and wheel. typically one is used on each side of the vehicle
helical gears - ANSWERS-gears that have teeth set on angle to the gear face they
operate more quietly than spur gears
