TFM01 EXTINGUISHER STATUTES AND
RULES 2026 STUDY MANUAL REGULATORY
REVIEW
◉ A firm or individual whose registration certificate or license has
been expired for 90 days or less may renew the certificate or license
by paying to the department:
Answer: the required renewal fee; and a fee equal to one-half of the
initial fee for the certificate or license.
◉ Any NOTICE OF EXPIRATION is relay to the right parties within
Answer: 30 days
◉ A firm or individual whose registration certificate or license has
been expired for more than 90 days but less than two years may
renew the certificate or license by paying to the department
Answer: all unpaid renewal fees; and a fee that is equal to the initial
fee for the certificate or license
◉ A firm or individual whose registration certificate or license has
been expired for ______ or longer may not renew the certificate or
license. The firm or individual may obtain a new registration
,certificate or license by complying with the requirements and
procedures for obtaining an initial registration certificate or license
Answer: 2 years
◉ All shop drawings must bear the signature of a___________, his
license number, the date of installation, and the certificate-of-
registration number of the registered firm
Answer: Type PL licensee
◉ Fixed temp-sensing element of fusible metal alloy type replaced
while servicing a kitchen hood ext. system must have a:
Answer: manufacture date stamp which must be in one year of the
replacement
◉ A rubber stamp may be used to supply the required information;
however, a stamped signature is prohibited. If a rubber stamp is
used, it shall produce an imprint __________________ all in boldface type
and capital letters and in the following sample format,_______.
Answer: -2 1/2 inches wide by one inch high,
-a stamped signature is prohibited
◉ After an installation has been completed, an installation label
must be affixed to the __________________. The signature of the licensee
on the label certifies that the system has been installed according to
law.
, Answer: control head or panel of the fixed fire extinguisher system.
◉ Installation Labels for Fixed Extinguisher Systems: Labels must
be_______ inches in height and _____ inches in width and must be of
the gum label type. They must not be red in color
Answer: -5
-4
◉ Fixed Extinguisher Systems: Installation labels must contain only
the following information in the format of the label shown in
subsection (b) of this section: * identification of the manufacturer's
manual(s) used for installation. and
Answer: * identification of the manufacturer's manual(s) used for
installation. and
*the inscription "DO NOT REMOVE BY ORDER OF THE STATE FIRE
MARSHAL--SYSTEM INSTALLATION RECORD" (all in capital letters,
at least 10-point boldface type);
*the firm's name, address, and telephone number;
*the firm's certificate-of-registration number;
*the signature and license number of the licensee authorized to
certify a fixed fire extinguishing system (a stamped signature is
prohibited); the date of installation
◉ After completion of the installation, modification, or addition of a
fixed fire extinguisher system, the licensee must complete an
RULES 2026 STUDY MANUAL REGULATORY
REVIEW
◉ A firm or individual whose registration certificate or license has
been expired for 90 days or less may renew the certificate or license
by paying to the department:
Answer: the required renewal fee; and a fee equal to one-half of the
initial fee for the certificate or license.
◉ Any NOTICE OF EXPIRATION is relay to the right parties within
Answer: 30 days
◉ A firm or individual whose registration certificate or license has
been expired for more than 90 days but less than two years may
renew the certificate or license by paying to the department
Answer: all unpaid renewal fees; and a fee that is equal to the initial
fee for the certificate or license
◉ A firm or individual whose registration certificate or license has
been expired for ______ or longer may not renew the certificate or
license. The firm or individual may obtain a new registration
,certificate or license by complying with the requirements and
procedures for obtaining an initial registration certificate or license
Answer: 2 years
◉ All shop drawings must bear the signature of a___________, his
license number, the date of installation, and the certificate-of-
registration number of the registered firm
Answer: Type PL licensee
◉ Fixed temp-sensing element of fusible metal alloy type replaced
while servicing a kitchen hood ext. system must have a:
Answer: manufacture date stamp which must be in one year of the
replacement
◉ A rubber stamp may be used to supply the required information;
however, a stamped signature is prohibited. If a rubber stamp is
used, it shall produce an imprint __________________ all in boldface type
and capital letters and in the following sample format,_______.
Answer: -2 1/2 inches wide by one inch high,
-a stamped signature is prohibited
◉ After an installation has been completed, an installation label
must be affixed to the __________________. The signature of the licensee
on the label certifies that the system has been installed according to
law.
, Answer: control head or panel of the fixed fire extinguisher system.
◉ Installation Labels for Fixed Extinguisher Systems: Labels must
be_______ inches in height and _____ inches in width and must be of
the gum label type. They must not be red in color
Answer: -5
-4
◉ Fixed Extinguisher Systems: Installation labels must contain only
the following information in the format of the label shown in
subsection (b) of this section: * identification of the manufacturer's
manual(s) used for installation. and
Answer: * identification of the manufacturer's manual(s) used for
installation. and
*the inscription "DO NOT REMOVE BY ORDER OF THE STATE FIRE
MARSHAL--SYSTEM INSTALLATION RECORD" (all in capital letters,
at least 10-point boldface type);
*the firm's name, address, and telephone number;
*the firm's certificate-of-registration number;
*the signature and license number of the licensee authorized to
certify a fixed fire extinguishing system (a stamped signature is
prohibited); the date of installation
◉ After completion of the installation, modification, or addition of a
fixed fire extinguisher system, the licensee must complete an
