MSSC QUALITY PRACTICE
EXAMINATION 2026 QUESTIONS
WITH ANSWERS GRADED A+
◍ Automated part inspection commonly uses __________..
Answer: vision systems
◍ Which is NOT one of the steps used in the glass box method?.
Answer: rotate object in glass box
◍ _____________ inspections assure that the equipment, personnel and
processes being used are providing the desired results and allow systems to
be pinpointed and solutions implemented before the problem can escalate..
Answer: In-process
◍ When parts need further inspection they should be labeled as ______..
Answer: Hold
◍ The three standard views of an object are ______..
Answer: top, front, right side
◍ What is the order of precedence of lines in a drawing?.
Answer: object, hidden, center
◍ What type of feature is parallel to the surface being dimensioned?.
Answer: dimension line
◍ Red tags are typically attached to parts that are __________..
Answer: scrapped
◍ A ______ dimension is described in inches per foot..
Answer: shaft taper
◍ The cost of a product's raw materials does not typically determine if
, __________..
Answer: the product is non-conforming
◍ Parts that are labeled as ok To ship must _________..
Answer: meet compliance
◍ Measurement of product quality attributes can be assisted by performing
__________..
Answer: daily quality and equipment checks
◍ To establish on a drawing that 1/4 inch equals 1 inch, the designer would
write ______..
Answer: 1/4 = 1
◍ Section lines on a blueprint include _______..
Answer: a surface that has been cut
◍ In a threaded fastener assembly what is designed to protect the threads?.
Answer: shank
◍ The sampling plan uses a(n) _________ chart that indicates to an inspector
the number of parts to inspect based on the size of the product batch..
Answer: frequency
◍ Certain characteristics of parts are essential for its proper operation.
Identifying these characteristics as _______ helps set up a meaningful
quality inspection program..
Answer: critical
◍ The minor diameter of a screw thread is measured at the ______..
Answer: root of screw thread
◍ An engineering change notice (ECN) is used to notify changes to
__________..
Answer: a product drawing
◍ The minor diameter of a threaded fastener is ______..
Answer: the major diameter minus the thread height
, ◍ The review of audit procedures and instructions are control and planning
functions within a(n) __________..
Answer: traceability program
◍ How do you determine the grade of a bolt?.
Answer: number of lines on the head +2 indicates the grade
◍ A screw with National fine thread is represented on a drawing with what
designation?.
Answer: NF
◍ A ___________ is used to verify that the proper procedures and processes
are being adhered to by plant personnel..
Answer: quality audit program
◍ Metals treated by ______ processes become soft..
Answer: annealing
◍ Instrument reliability is examined to determine _____________________..
Answer: calibration intervals
◍ The calibration of instruments and measurement devices is typically
checked as a part of a _______________..
Answer: quality audit
◍ A running fit is also called a(n) ______..
Answer: sliding fit
◍ The term ______ refers to a physical portion of a part..
Answer: feature
◍ A(n) _______ is a theoretically perfect line, point or pane that is located by
a similar feature or part..
Answer: datum
◍ Machine time, task time, and quality requirements are information needed to
__________..
Answer: document each process
EXAMINATION 2026 QUESTIONS
WITH ANSWERS GRADED A+
◍ Automated part inspection commonly uses __________..
Answer: vision systems
◍ Which is NOT one of the steps used in the glass box method?.
Answer: rotate object in glass box
◍ _____________ inspections assure that the equipment, personnel and
processes being used are providing the desired results and allow systems to
be pinpointed and solutions implemented before the problem can escalate..
Answer: In-process
◍ When parts need further inspection they should be labeled as ______..
Answer: Hold
◍ The three standard views of an object are ______..
Answer: top, front, right side
◍ What is the order of precedence of lines in a drawing?.
Answer: object, hidden, center
◍ What type of feature is parallel to the surface being dimensioned?.
Answer: dimension line
◍ Red tags are typically attached to parts that are __________..
Answer: scrapped
◍ A ______ dimension is described in inches per foot..
Answer: shaft taper
◍ The cost of a product's raw materials does not typically determine if
, __________..
Answer: the product is non-conforming
◍ Parts that are labeled as ok To ship must _________..
Answer: meet compliance
◍ Measurement of product quality attributes can be assisted by performing
__________..
Answer: daily quality and equipment checks
◍ To establish on a drawing that 1/4 inch equals 1 inch, the designer would
write ______..
Answer: 1/4 = 1
◍ Section lines on a blueprint include _______..
Answer: a surface that has been cut
◍ In a threaded fastener assembly what is designed to protect the threads?.
Answer: shank
◍ The sampling plan uses a(n) _________ chart that indicates to an inspector
the number of parts to inspect based on the size of the product batch..
Answer: frequency
◍ Certain characteristics of parts are essential for its proper operation.
Identifying these characteristics as _______ helps set up a meaningful
quality inspection program..
Answer: critical
◍ The minor diameter of a screw thread is measured at the ______..
Answer: root of screw thread
◍ An engineering change notice (ECN) is used to notify changes to
__________..
Answer: a product drawing
◍ The minor diameter of a threaded fastener is ______..
Answer: the major diameter minus the thread height
, ◍ The review of audit procedures and instructions are control and planning
functions within a(n) __________..
Answer: traceability program
◍ How do you determine the grade of a bolt?.
Answer: number of lines on the head +2 indicates the grade
◍ A screw with National fine thread is represented on a drawing with what
designation?.
Answer: NF
◍ A ___________ is used to verify that the proper procedures and processes
are being adhered to by plant personnel..
Answer: quality audit program
◍ Metals treated by ______ processes become soft..
Answer: annealing
◍ Instrument reliability is examined to determine _____________________..
Answer: calibration intervals
◍ The calibration of instruments and measurement devices is typically
checked as a part of a _______________..
Answer: quality audit
◍ A running fit is also called a(n) ______..
Answer: sliding fit
◍ The term ______ refers to a physical portion of a part..
Answer: feature
◍ A(n) _______ is a theoretically perfect line, point or pane that is located by
a similar feature or part..
Answer: datum
◍ Machine time, task time, and quality requirements are information needed to
__________..
Answer: document each process
