Cisco
500-220 Exam
Engineering Cisco Meraki Solutions Exam
Questions & Answers (Demo Version)
https://dumps2go.com/dumps/500-220/
Buy Full Product Here:
, Cisco
500-220 Exam
Engineering Cisco Meraki Solution
Questions & Answers
Demo
,Questions & Answers PDF Page 2
Version: 4.0
Question: 1
DRAG DROP
Drag and drop the descriptions from the left onto the corresponding MX operation mode on the right.
Answer:
,Questions & Answers PDF Page 3
Question: 2
When an SSID is configured with Sign-On Splash page enabled, which two settings must be configured for
unauthenticated clients to have full network access and not be allow listed? (Choose two.)
A. Controller disconnection behavior
B. Captive Portal strength
C. Simultaneous logins
D. Firewall & traffic shaping
E. RADIUS for splash page settings
Answer: AB
Reference: https://documentation.meraki.com/MR/Access_Control
Question: 3
Refer to the exhibit.
,Questions & Answers PDF Page 4
Assuming this MX has established a full tunnel with its VPN peer, how will the MX route the WebEx
traffic?
A. WebEx traffic will prefer WAN 2 as long as it meets the thresholds in the “Conf” performance class.
B. WebEx traffic will prefer WAN 1 as it is the primary uplink.
C. WebEx traffic will prefer WAN 2 as long as it is up.
D. WebEx traffic will be load-balanced between both active WAN links.
Answer: B
Question: 4
For which two reasons can an organization become “Out of License”? (Choose two.)
A. licenses that are in the wrong network
B. more hardware devices than device licenses
C. expired device license
D. licenses that do not match the serial numbers in the organization
E. MR licenses that do not match the MR models in the organization
Answer: BC
, Questions & Answers PDF Page 5
Reference:
https://documentation.meraki.com/General_Administration/Licensing/Meraki_Licensing_FAQs
Question: 5
Refer to the exhibit.
Which two actions are required to optimize load balancing asymmetrically with a 4:1 ratio between
links? (Choose two.)
A. Change the primary uplink to "none".
B. Add an internet traffic preference that defines the load-balancing ratio as 4:1.
C. Enable load balancing.
D. Set the speed of the cellular uplink to zero.
E. Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1.
Answer: BC
500-220 Exam
Engineering Cisco Meraki Solutions Exam
Questions & Answers (Demo Version)
https://dumps2go.com/dumps/500-220/
Buy Full Product Here:
, Cisco
500-220 Exam
Engineering Cisco Meraki Solution
Questions & Answers
Demo
,Questions & Answers PDF Page 2
Version: 4.0
Question: 1
DRAG DROP
Drag and drop the descriptions from the left onto the corresponding MX operation mode on the right.
Answer:
,Questions & Answers PDF Page 3
Question: 2
When an SSID is configured with Sign-On Splash page enabled, which two settings must be configured for
unauthenticated clients to have full network access and not be allow listed? (Choose two.)
A. Controller disconnection behavior
B. Captive Portal strength
C. Simultaneous logins
D. Firewall & traffic shaping
E. RADIUS for splash page settings
Answer: AB
Reference: https://documentation.meraki.com/MR/Access_Control
Question: 3
Refer to the exhibit.
,Questions & Answers PDF Page 4
Assuming this MX has established a full tunnel with its VPN peer, how will the MX route the WebEx
traffic?
A. WebEx traffic will prefer WAN 2 as long as it meets the thresholds in the “Conf” performance class.
B. WebEx traffic will prefer WAN 1 as it is the primary uplink.
C. WebEx traffic will prefer WAN 2 as long as it is up.
D. WebEx traffic will be load-balanced between both active WAN links.
Answer: B
Question: 4
For which two reasons can an organization become “Out of License”? (Choose two.)
A. licenses that are in the wrong network
B. more hardware devices than device licenses
C. expired device license
D. licenses that do not match the serial numbers in the organization
E. MR licenses that do not match the MR models in the organization
Answer: BC
, Questions & Answers PDF Page 5
Reference:
https://documentation.meraki.com/General_Administration/Licensing/Meraki_Licensing_FAQs
Question: 5
Refer to the exhibit.
Which two actions are required to optimize load balancing asymmetrically with a 4:1 ratio between
links? (Choose two.)
A. Change the primary uplink to "none".
B. Add an internet traffic preference that defines the load-balancing ratio as 4:1.
C. Enable load balancing.
D. Set the speed of the cellular uplink to zero.
E. Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1.
Answer: BC
