AQA A-Level DESIGN AND TECHNOLOGY: FASHION AND TEXTILES Paper
2 Designing and Making Principles QP June 2020
Please write clearly in block capitals.
Centre number Candidate number
Surname ________________________________________________________________________
Forename(s) ________________________________________________________________________
Candidate signature ________________________________________________________________________
I declare this is my own work.
A-level
DESIGN AND TECHNOLOGY:
FASHION AND TEXTILES
Paper 2 Designing and Making Principles
Friday 12 June 2020 Morning Time allowed: 1 hour 30 minutes
Materials For Examiner’s Use
For this paper you must have:
normal writing and drawing instruments Question Mark
a scientific calculator.
1
Instructions 2
Use black ink or black ball-point pen. Use pencil only for drawing.
Fill in the boxes at the top of this page. 3
Answer all questions. 4
You must answer the questions in the spaces provided. Do not write outside
the box around each page or on blank pages. 5
If you need extra space for your answer(s), use the lined pages at the end of
6
this book. Write the question number against your answer(s).
Do all rough work in this book. Cross through any work you do not want 7–9
to be marked.
10
Information 11
The marks for questions are shown in brackets.
The maximum mark for this paper is 80. 12
There are 30 marks for Section A and 50 marks for Section B.
TOTAL
(JUN207562201)
G/KL/Jun20/E5 7562/2
, 2
Do not write
outside the
box
Section A – Product Analysis
Answer all questions in this section.
0 1 Figure 1
Denim shirt
Figure 2
Denim waistcoat
(02)
G/Jun20/7562/2
, 3
Do not write
outside the
box
0 1 . 1 Compare and contrast the decorative techniques applied to the denim garments in
Figure 1 and Figure 2.
[6 marks]
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
0 1 . 2 Identify three different ways in which automated manufacturing could be used to
manufacture parts of the denim shirt in Figure 1.
[3 marks]
1 _________________________________________________________________________________
___________________________________________________________________________________
2 _________________________________________________________________________________
___________________________________________________________________________________
3 _________________________________________________________________________________
___________________________________________________________________________________
Turn over 8
(03)
G/Jun20/7562/2
2 Designing and Making Principles QP June 2020
Please write clearly in block capitals.
Centre number Candidate number
Surname ________________________________________________________________________
Forename(s) ________________________________________________________________________
Candidate signature ________________________________________________________________________
I declare this is my own work.
A-level
DESIGN AND TECHNOLOGY:
FASHION AND TEXTILES
Paper 2 Designing and Making Principles
Friday 12 June 2020 Morning Time allowed: 1 hour 30 minutes
Materials For Examiner’s Use
For this paper you must have:
normal writing and drawing instruments Question Mark
a scientific calculator.
1
Instructions 2
Use black ink or black ball-point pen. Use pencil only for drawing.
Fill in the boxes at the top of this page. 3
Answer all questions. 4
You must answer the questions in the spaces provided. Do not write outside
the box around each page or on blank pages. 5
If you need extra space for your answer(s), use the lined pages at the end of
6
this book. Write the question number against your answer(s).
Do all rough work in this book. Cross through any work you do not want 7–9
to be marked.
10
Information 11
The marks for questions are shown in brackets.
The maximum mark for this paper is 80. 12
There are 30 marks for Section A and 50 marks for Section B.
TOTAL
(JUN207562201)
G/KL/Jun20/E5 7562/2
, 2
Do not write
outside the
box
Section A – Product Analysis
Answer all questions in this section.
0 1 Figure 1
Denim shirt
Figure 2
Denim waistcoat
(02)
G/Jun20/7562/2
, 3
Do not write
outside the
box
0 1 . 1 Compare and contrast the decorative techniques applied to the denim garments in
Figure 1 and Figure 2.
[6 marks]
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
0 1 . 2 Identify three different ways in which automated manufacturing could be used to
manufacture parts of the denim shirt in Figure 1.
[3 marks]
1 _________________________________________________________________________________
___________________________________________________________________________________
2 _________________________________________________________________________________
___________________________________________________________________________________
3 _________________________________________________________________________________
___________________________________________________________________________________
Turn over 8
(03)
G/Jun20/7562/2
