3/8/2019 Review Test Submission: TOM Homework 3 - Process Analysis &...
Course OPERATIONS MANAGEMENT
Test TOM Homework 3 - Process Analysis
Started 2/4/19 9:12 PM
Submitted 2/4/19 10:04 PM
Due Date 2/5/19 8:00 AM
Status Completed
Comments Gave you the benefit of the doubt on Q2,4, and 6 for the Capacity (it seems that you entered the capacity
utilization value instead of capacity), but be sure to read these carefully in the exam.
Attempt 13 out of 15 points
Score
Time 51 minutes
Elapsed
Results All Answers, Submitted Answers, Correct Answers
Displayed
Question 1 1 out of 1 points
Concordia Corporation case on page 4 describes Production and Engineering. Based on the information
provided in first paragraph of that section, how long is the Concordia's workday in minutes? (Hint: calculate
how total minutes worked during the workday in minutes/day)
Selected Answer: 480
Correct Answer: 480
Answer range +/- 2 (478.0 - 482.0)
Question 2 1 out of 1 points
(500) What is the calculated Capacity for Step 14: Final Inspection? (round to 2 decimal places)
Selected Answer: 90.28
Correct Answer: 553.85
Answer range +/- 2 (551.85 - 555.85)
Question 3 1 out of 1 points
(500) What is the calculated Capacity Utilization for Step 14: Final Inspection? (round to whole percent)
Selected Answer: 90
Correct Answer: 90
Answer range +/- 1 (89.0 - 91.0)
Question 4 1 out of 1 points
(500) What is the calculated Capacity for Step 9: Mold gromemet inserter? (round to 2 decimal places)
Selected Answer: 67.71
Correct Answer: 738.46
Answer range +/- 2 (736.46 - 740.46)
Question 5 1 out of 1 points
(500) What is the calculated Capacity Utilization for Step 8: Spot tape and tubing? (round to whole percent)
This study source was downloaded by 100000858936669 from CourseHero.com on 01-28-2023 18:06:13 GMT -06:00
https://blackboard.babson.edu/webapps/assessment/review/review.jsp?attempt_id=_1552923_1&course_id=_20223_1&content_id=_1026349_1&outc… 1/3
https://www.coursehero.com/file/38750787/TOM-Homework-3-Process-Analysispdf/
Course OPERATIONS MANAGEMENT
Test TOM Homework 3 - Process Analysis
Started 2/4/19 9:12 PM
Submitted 2/4/19 10:04 PM
Due Date 2/5/19 8:00 AM
Status Completed
Comments Gave you the benefit of the doubt on Q2,4, and 6 for the Capacity (it seems that you entered the capacity
utilization value instead of capacity), but be sure to read these carefully in the exam.
Attempt 13 out of 15 points
Score
Time 51 minutes
Elapsed
Results All Answers, Submitted Answers, Correct Answers
Displayed
Question 1 1 out of 1 points
Concordia Corporation case on page 4 describes Production and Engineering. Based on the information
provided in first paragraph of that section, how long is the Concordia's workday in minutes? (Hint: calculate
how total minutes worked during the workday in minutes/day)
Selected Answer: 480
Correct Answer: 480
Answer range +/- 2 (478.0 - 482.0)
Question 2 1 out of 1 points
(500) What is the calculated Capacity for Step 14: Final Inspection? (round to 2 decimal places)
Selected Answer: 90.28
Correct Answer: 553.85
Answer range +/- 2 (551.85 - 555.85)
Question 3 1 out of 1 points
(500) What is the calculated Capacity Utilization for Step 14: Final Inspection? (round to whole percent)
Selected Answer: 90
Correct Answer: 90
Answer range +/- 1 (89.0 - 91.0)
Question 4 1 out of 1 points
(500) What is the calculated Capacity for Step 9: Mold gromemet inserter? (round to 2 decimal places)
Selected Answer: 67.71
Correct Answer: 738.46
Answer range +/- 2 (736.46 - 740.46)
Question 5 1 out of 1 points
(500) What is the calculated Capacity Utilization for Step 8: Spot tape and tubing? (round to whole percent)
This study source was downloaded by 100000858936669 from CourseHero.com on 01-28-2023 18:06:13 GMT -06:00
https://blackboard.babson.edu/webapps/assessment/review/review.jsp?attempt_id=_1552923_1&course_id=_20223_1&content_id=_1026349_1&outc… 1/3
https://www.coursehero.com/file/38750787/TOM-Homework-3-Process-Analysispdf/
