NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND
ANSWERS (COMPLETED)
Dew point is the temperature at which - answercondensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being
applied. After application of the 19 coat you notice small blisters in some areas of the applied
lining. Your FIRST preferred course of action is to: - answerDocument the problem and advise the
Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning
and conventional airspray, the coating inspector should perform a - answerblotter test for the
presence of oil and water.
Upon arrival of coating materials, the inspector should - answerobserve and document the amount
of material and batch numbers.
Relative humidity is - answera measure of the amount of moisture in the air compared to
saturation level.
Galvanic corrosion occurs on which of the following substrates? - answerMetal
When applying Thermal Spray Coatings the specification is most likely to reference: -
answerSSPC-CS 23.00/AWS C2.23/NACE No. 12
What is the minimum recommended distance away from an edge that an inspector should take a
measurement with a dial type magnetic pull off Dry Film Thickness(DFT) gauge? - answer2.5 cm (1
inch)
Polymerization is the process of? - answerMonomers joining together.
An exposed area of the substrate or previous coat of a conductive material, often caused by poor
application technique is called: - answerHoliday
, NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND
ANSWERS (COMPLETED)
Checking is: - answera fine crack in the surface of a coating that rarely reaches the substrate.
Inspection documentation is important because: - answerOwners use the documentation for a
variety of purposes.
An Inspectors personal log book should contain: - answerNo comments regarding the application
team.
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team
of uncertified field pipeline inspectors. Your FIRST preferred course of action is to: - answerReview
the NACE Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information about ALL of the
following EXCEPT: - answerHow the item was coated.
Non Conformance Reports are completed by the Inspector: - answerWhen the Inspector and
Contractor deem it to be significant non conforming item.
The initial steel condition is important to the NACE Inspector because: - answerThe Inspector may
have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic failure is: -
answerGalvanic Corrosion
What is used to determine compressed air cleanliness? - answerProfilometer
Osmotic blistering is most likely to occur as a result of: - answerAirless spray application.
When performing tests for oil and grease using an ultra violet light, the NACE Inspector should be
aware that: - answerSynthetic oil or grease may not be identified.
, NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND
ANSWERS (COMPLETED)
To achieve consistently accurate results with ALL alt test equipment: - answerwash your hands
before sampling.
When holiday testing is required the Inspector is always required to enforce what standard? -
answerNACE SP 0188
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default
restriction level is: - answerLevel 3
Fine cracks in the surface of a coating that rarely reach the substrate are called: - answerChecking
It is good practice for the NACE Inspector to have instrument calibration certificates available: -
answerAt all times.
In a non convertible coating the role of the primary solvent is to: - answerTo control the
evaporation rate.
Removal of weld splatter is required: - answerWhen specifically identified in the owners
specification.
Common errors that may produce inaccurate readings when using a Dial Type Magnetic Pull Off
Dry Film Thickness(DFT) gauge include: - answerFailing to determine the Base Metal
Reading(BMR),Rotating the dial too fast when taking measurements, and Measuring ditty, tacky,
or soft films.
Conventional spray us good choice when: - answerHigh quality finishes are required.
Which of these tests uses a syringe? - answerBresle Patch
Which one of these elements is not necessary for corrosion to occur: - answerReference Cell
ANSWERS (COMPLETED)
Dew point is the temperature at which - answercondensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being
applied. After application of the 19 coat you notice small blisters in some areas of the applied
lining. Your FIRST preferred course of action is to: - answerDocument the problem and advise the
Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning
and conventional airspray, the coating inspector should perform a - answerblotter test for the
presence of oil and water.
Upon arrival of coating materials, the inspector should - answerobserve and document the amount
of material and batch numbers.
Relative humidity is - answera measure of the amount of moisture in the air compared to
saturation level.
Galvanic corrosion occurs on which of the following substrates? - answerMetal
When applying Thermal Spray Coatings the specification is most likely to reference: -
answerSSPC-CS 23.00/AWS C2.23/NACE No. 12
What is the minimum recommended distance away from an edge that an inspector should take a
measurement with a dial type magnetic pull off Dry Film Thickness(DFT) gauge? - answer2.5 cm (1
inch)
Polymerization is the process of? - answerMonomers joining together.
An exposed area of the substrate or previous coat of a conductive material, often caused by poor
application technique is called: - answerHoliday
, NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND
ANSWERS (COMPLETED)
Checking is: - answera fine crack in the surface of a coating that rarely reaches the substrate.
Inspection documentation is important because: - answerOwners use the documentation for a
variety of purposes.
An Inspectors personal log book should contain: - answerNo comments regarding the application
team.
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team
of uncertified field pipeline inspectors. Your FIRST preferred course of action is to: - answerReview
the NACE Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information about ALL of the
following EXCEPT: - answerHow the item was coated.
Non Conformance Reports are completed by the Inspector: - answerWhen the Inspector and
Contractor deem it to be significant non conforming item.
The initial steel condition is important to the NACE Inspector because: - answerThe Inspector may
have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic failure is: -
answerGalvanic Corrosion
What is used to determine compressed air cleanliness? - answerProfilometer
Osmotic blistering is most likely to occur as a result of: - answerAirless spray application.
When performing tests for oil and grease using an ultra violet light, the NACE Inspector should be
aware that: - answerSynthetic oil or grease may not be identified.
, NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND
ANSWERS (COMPLETED)
To achieve consistently accurate results with ALL alt test equipment: - answerwash your hands
before sampling.
When holiday testing is required the Inspector is always required to enforce what standard? -
answerNACE SP 0188
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default
restriction level is: - answerLevel 3
Fine cracks in the surface of a coating that rarely reach the substrate are called: - answerChecking
It is good practice for the NACE Inspector to have instrument calibration certificates available: -
answerAt all times.
In a non convertible coating the role of the primary solvent is to: - answerTo control the
evaporation rate.
Removal of weld splatter is required: - answerWhen specifically identified in the owners
specification.
Common errors that may produce inaccurate readings when using a Dial Type Magnetic Pull Off
Dry Film Thickness(DFT) gauge include: - answerFailing to determine the Base Metal
Reading(BMR),Rotating the dial too fast when taking measurements, and Measuring ditty, tacky,
or soft films.
Conventional spray us good choice when: - answerHigh quality finishes are required.
Which of these tests uses a syringe? - answerBresle Patch
Which one of these elements is not necessary for corrosion to occur: - answerReference Cell
