General Contractor Trade Exam Test 2 Questions and
Answers 2023 with complete solution
brick on a job site should be covered
when you leave at the end of the day
how long should tile set on a organic adhesive bed in order to cure
24 hours
what is the correct space (gap) between a finished floor and bottom of an interior
door with no threshold
1/2"
what are as built plans
plans showing all changes and repair
can you directly nail hardwood flooring to a concrete slab
no you should never nail it directly
interior carpet should be installed with
tackless strips
before applying latex paint to the surface of an oil paint on wood trim which
procedure is appropriate
wash with tsp
handicap sinks should have what kind of drains
wrapped
handicap restrooms should have
a min of 48" maneuverable space in front of toilet
lever handles on faucet
wrapped drain lines
an MSDS should be kept at
jobsite
a stove unit without insulation must be how many inches away from combustible
material?
6"
a tee-wye is a
plumbing fitting
when screw are used instead of nails. the required spacing between screws is
usually
larger
where is a 4-prong outlet plug used
at the service to house trailer or RV vehicle
the function of a waler is
horizontal member used to align and brace concrete forms or piles
what should you do after discovering asbestos on the job
contact chief of DOSH
what is the best method for installing ceramic tiles
on cement board with thinnest adhesive
in a commercial or publicly funded building which is required when a handicap
sink is open underneath
, surface no higher than 34"
knee clearance of at least 30"
no sharp edge underneath
when must the contractor provide the warranty for a water heater to the property
owner
on completion of installation at the job site
what is the proper order of construction for the following building trades
framing, plumbing, electrical, insulation
of the following which method is best for attaching particle board underlayment
to subflooring for resilient floor tile?
1/4 inch staples
how much freon can be removed from equipment during servicing without using
a recovery system
zero lbs
bricks on a job site should be covered
when you leave the end of workday
how long should tile set on an organic adhesive bed in order to cure
24 hours
what is the requirement for vents under a raised floor
1.5 sq ft for every 25 linear feet
Which formula would you use to determine the quantity of drywall needed for a
wall of a room
ceiling height x wall length
of the following which is the most dangerous effect of air bubbles in mortar
weakens mortar strength
when used as a joist which horizontal beam is stronger
2" x 12"
what is the min width of a handicap access door
36"
a stairway's max total riser and tread dimensions would be
2 risers + 1 tread = 25"
which of the following is a measure of power load
watts
the max weather exposure for 18" wood shingle is
4-6 inches
the max weathering exposure for 18" wood shingles is
4-6 inch
what is the tolerance on effective depth when placing rebar in a slab more than 8"
thick?
+/- 1/2"
what is the tolerance on longitudinal placement of rebar when the bar is bent at
both ends
+/- 1/2"
what is the tolerance on longitudinal placement of rebar when the bar is bent at
one end?
+ 0" , -1/2"
Answers 2023 with complete solution
brick on a job site should be covered
when you leave at the end of the day
how long should tile set on a organic adhesive bed in order to cure
24 hours
what is the correct space (gap) between a finished floor and bottom of an interior
door with no threshold
1/2"
what are as built plans
plans showing all changes and repair
can you directly nail hardwood flooring to a concrete slab
no you should never nail it directly
interior carpet should be installed with
tackless strips
before applying latex paint to the surface of an oil paint on wood trim which
procedure is appropriate
wash with tsp
handicap sinks should have what kind of drains
wrapped
handicap restrooms should have
a min of 48" maneuverable space in front of toilet
lever handles on faucet
wrapped drain lines
an MSDS should be kept at
jobsite
a stove unit without insulation must be how many inches away from combustible
material?
6"
a tee-wye is a
plumbing fitting
when screw are used instead of nails. the required spacing between screws is
usually
larger
where is a 4-prong outlet plug used
at the service to house trailer or RV vehicle
the function of a waler is
horizontal member used to align and brace concrete forms or piles
what should you do after discovering asbestos on the job
contact chief of DOSH
what is the best method for installing ceramic tiles
on cement board with thinnest adhesive
in a commercial or publicly funded building which is required when a handicap
sink is open underneath
, surface no higher than 34"
knee clearance of at least 30"
no sharp edge underneath
when must the contractor provide the warranty for a water heater to the property
owner
on completion of installation at the job site
what is the proper order of construction for the following building trades
framing, plumbing, electrical, insulation
of the following which method is best for attaching particle board underlayment
to subflooring for resilient floor tile?
1/4 inch staples
how much freon can be removed from equipment during servicing without using
a recovery system
zero lbs
bricks on a job site should be covered
when you leave the end of workday
how long should tile set on an organic adhesive bed in order to cure
24 hours
what is the requirement for vents under a raised floor
1.5 sq ft for every 25 linear feet
Which formula would you use to determine the quantity of drywall needed for a
wall of a room
ceiling height x wall length
of the following which is the most dangerous effect of air bubbles in mortar
weakens mortar strength
when used as a joist which horizontal beam is stronger
2" x 12"
what is the min width of a handicap access door
36"
a stairway's max total riser and tread dimensions would be
2 risers + 1 tread = 25"
which of the following is a measure of power load
watts
the max weather exposure for 18" wood shingle is
4-6 inches
the max weathering exposure for 18" wood shingles is
4-6 inch
what is the tolerance on effective depth when placing rebar in a slab more than 8"
thick?
+/- 1/2"
what is the tolerance on longitudinal placement of rebar when the bar is bent at
both ends
+/- 1/2"
what is the tolerance on longitudinal placement of rebar when the bar is bent at
one end?
+ 0" , -1/2"
