MSSC Certification Exam QUESTIONS WITH CORRECT ANSWERS UPDATE 2023

MSSC Certification Exam QUESTIONS WITH CORRECT ANSWERS UPDATE 2023 What are the two types of assembly drawings? - ANSWER Exploded and basic The three standard views of an object are ____________ - ANSWER top, front, right side Geometric dimensioning and tolerances refers to tolerances which control - ANSWER Form, profile, orientation, location, and runout Which type of feature is parallel to the surface being dimensioned? - ANSWER dimension lines To establish on a drawing that 1/8 inch equals 1 inch, the designer would write ____________. - ANSWER 1/8 = 1 If the feature on the drawing is drawn 2 inched long and the scale is 1:4, what is the actual dimension of the object? - ANSWER 8" If a box of parts weighs 30 pounds, how many kilograms does it weigh? - ANSWER 13.6 kilograms The acronym, ECN, stands for: - ANSWER Engineering Change Notice A capable manufacturing process tends to run - ANSWER out of control The acronym, SPC, stands for - ANSWER Statistical process control Adjustments in follow-up with product quality checks are necessary in a/an _______ non-conformity - ANSWER Product process and system Recommendations for corrective action are the responsibility of - ANSWER All knowledgeable persons To convert inches to millimeters, multiply inches by: - ANSWER 25.4 Identify a device that measures length to an accuracy of 0.001 inch. - ANSWER Micrometer A ________ is the total amount by which a specified dimension is allowed to vary and still be a good part - ANSWER tolerance Which of the following measurement tools should be selected to measure a part that has a length specification of 1.625 inches +/- 0.005? - ANSWER micrometer A part measures 45.70 mm in a process with the tolerance of 46mm + or - .28 is considered ____________. - ANSWER Out of spec, below the lower tolerance limit When connected to a PC, a digital caliper can be used to: - ANSWER Collect SPC data The equipment at a workstation is supposed to produce parts at 2.593. per the part drawing, and has a spec limit of + or - 0.004. is the part that has been produces at 2.590 out of spec? - ANSWER No, it is not out of spec Given a control chart that has 8 data points in the same direction the status of the process: - ANSWER Out of control - trend pattern Which of the following parts lengths is out of spec if the specification calls for a part length of 4.202 (+ or - 0.003)? - ANSWER 4.197 A program that allows a user to enter gage measurements in rows and columns of numbers, perform calculations, and produce a graph is called a - ANSWER Spreadsheet A running fit is also called a(n) ____________. - ANSWER Sliding Fit Which of the following decimals id the fraction 9/1000 converted to__________. - ANSWER 0.009 In the electronic field, the optical comparator uses which of the following as a means of inspecting parts? - ANSWER magnification The tolerance for a geometric feature can easily identified by reading the ____________. - ANSWER feature control frame ISO 9000 - ANSWER Documents standards within an organization Process quality can be improved by: - ANSWER Eliminating quality variances The first step in constructing a Cause and Effect diagram is to - ANSWER Write down the problem statement and draw a box around it Of the four classifications of quality costs, which one will provide the greatest dollar savings verses dollars spent? - ANSWER Prevention costs Two systems of dimensional measurement used in manufacturing are the SI Metric System and the ____________. - ANSWER US customary system Cause and Effect diagrams help during the _______ phase of the Plan-Do-Check-Act (PDCA) cycle - ANSWER planning Equipment historical data are used to - ANSWER Identify possible solutions to quality defects The measurement of a 5.000-inch part, with an instrument having ________ accuracy, should range from 4,998 - 5.002 inches. - ANSWER + or - 0.002 The conversion of 3-3/8 inches to decimal inches is__________. - ANSWER 3.375 inches When performing a Root Cause Analysis, after finding the cause of the defect, the next step should be to: - ANSWER Take corrective action immediately What is the most important item to appear on the calibration label of a tool that is used to measure and test equipment? - ANSWER The date the tool is due for calibration The MOST important measure of external quality is product performance as viewed b