Kentucky UST Certification Test Prep Exam Questions
Verified Answers (Latest Update 2023) GRADED A+
1. when tanks arrive at the job site, how should they be unloaded? - correct
answers ✅lifted off with a cable attached to the tank lifting lugs
As an alternative lifting method, should a cable or chain be wrapped around
the tank? - correct answers ✅No, Never!
When you are lifting a tank, using the lifting lugs, which of these procedures
should be followed? - correct answers ✅attach a triangle cable through the
lugs with no more than a 30 degree angle from the center line.
After you unload a new tank on a clean level surface at the job site what else
should you do prior to inspection and pre-testing? - correct answers
✅Chock the tank to prevent it from Rolling
which of the following items should be physically checked for damage or
imperfections at the job site? - correct answers ✅Piping (steel and
fiberglass)
Fittings, Vents, Fillboxes, anodes, ECT..
The tanks themselves
,Kentucky UST Certification Test Prep Exam Questions
Verified Answers (Latest Update 2023) GRADED A+
(ALL OF THE ABOVE)!
STI-P3 tanks are delivered with shipping plugs in tank openings. What should
be done to these plugs prior to testing? - correct answers ✅remove the
plugs and replace them with a standard threaded plug that is properly doped
should dielectric bushings be installed in all openings of an STI-P3 tank? -
correct answers ✅yes on all openings
what is the maximum air pressure to which a steel tank should be subjected
in a pre-installation test? - correct answers ✅5 pounds
for fiberglass reinforced plastic (FRP) tanks up to 12 feet in diameter what is
an acceptable air pressure to which the tanks may be subjected in a pre-
installation test? - correct answers ✅3 pounds
for FRP tanks over 12 feet in diameter what is the maximum air pressure to
which the tanks should be subjected in a pre-installation test? - correct
answers ✅3 pounds
,Kentucky UST Certification Test Prep Exam Questions
Verified Answers (Latest Update 2023) GRADED A+
when you are conducting an air test on a tank the type of gauge that should
be used is? - correct answers ✅a pressure gauge with a maximum limit of
10 to 15 PSIG
the proper procedure for conducting a pre-installation air test of a steel tank
is to? - correct answers ✅apply 3 to 5 pounds of pressure and soap all
surfaces and weld seams visible through the coating while inspecting for
bubbles.
what is the proper procedure for conducting a pre-installation air test of an
FRP tank Under 12 feet in diameter is to.... - correct answers ✅apply 3
pounds of air pressure and soap all surfaces while inspecting for any sign of a
leak either audible or visible in the form of bubbles on the surface
a double-walled steel tank build in accordance with UL standard 58 is? -
correct answers ✅requires air testing of the interstitial space prior to
installation
, Kentucky UST Certification Test Prep Exam Questions
Verified Answers (Latest Update 2023) GRADED A+
the proper procedure for conducting a pre-installation air test of a double-
walled tank is to? - correct answers ✅pressurize the inner tank monitor the
pressure for one hour and then pressurize the space between the inner and
outer tanks with the air from the inner tank
when shipped a steel tank is covered with a coating that is an important part
of the tanks Corrosion Prevention system. "holidays" which show up in the
coating at the installation site should? - correct answers ✅should be
touched up with a compatible coating after proper surface preparation
touch up of holidays in a steel tank coatings at the installation site should be
done....... - correct answers ✅according to the manufacturer's instructions
dielectric bushings are usually made of what? - correct answers ✅non-
metallic material
factors to consider in determining the size shape and depth of a tank
excavation include what? - correct answers ✅*the tank manufacturers
recommendations
Verified Answers (Latest Update 2023) GRADED A+
1. when tanks arrive at the job site, how should they be unloaded? - correct
answers ✅lifted off with a cable attached to the tank lifting lugs
As an alternative lifting method, should a cable or chain be wrapped around
the tank? - correct answers ✅No, Never!
When you are lifting a tank, using the lifting lugs, which of these procedures
should be followed? - correct answers ✅attach a triangle cable through the
lugs with no more than a 30 degree angle from the center line.
After you unload a new tank on a clean level surface at the job site what else
should you do prior to inspection and pre-testing? - correct answers
✅Chock the tank to prevent it from Rolling
which of the following items should be physically checked for damage or
imperfections at the job site? - correct answers ✅Piping (steel and
fiberglass)
Fittings, Vents, Fillboxes, anodes, ECT..
The tanks themselves
,Kentucky UST Certification Test Prep Exam Questions
Verified Answers (Latest Update 2023) GRADED A+
(ALL OF THE ABOVE)!
STI-P3 tanks are delivered with shipping plugs in tank openings. What should
be done to these plugs prior to testing? - correct answers ✅remove the
plugs and replace them with a standard threaded plug that is properly doped
should dielectric bushings be installed in all openings of an STI-P3 tank? -
correct answers ✅yes on all openings
what is the maximum air pressure to which a steel tank should be subjected
in a pre-installation test? - correct answers ✅5 pounds
for fiberglass reinforced plastic (FRP) tanks up to 12 feet in diameter what is
an acceptable air pressure to which the tanks may be subjected in a pre-
installation test? - correct answers ✅3 pounds
for FRP tanks over 12 feet in diameter what is the maximum air pressure to
which the tanks should be subjected in a pre-installation test? - correct
answers ✅3 pounds
,Kentucky UST Certification Test Prep Exam Questions
Verified Answers (Latest Update 2023) GRADED A+
when you are conducting an air test on a tank the type of gauge that should
be used is? - correct answers ✅a pressure gauge with a maximum limit of
10 to 15 PSIG
the proper procedure for conducting a pre-installation air test of a steel tank
is to? - correct answers ✅apply 3 to 5 pounds of pressure and soap all
surfaces and weld seams visible through the coating while inspecting for
bubbles.
what is the proper procedure for conducting a pre-installation air test of an
FRP tank Under 12 feet in diameter is to.... - correct answers ✅apply 3
pounds of air pressure and soap all surfaces while inspecting for any sign of a
leak either audible or visible in the form of bubbles on the surface
a double-walled steel tank build in accordance with UL standard 58 is? -
correct answers ✅requires air testing of the interstitial space prior to
installation
, Kentucky UST Certification Test Prep Exam Questions
Verified Answers (Latest Update 2023) GRADED A+
the proper procedure for conducting a pre-installation air test of a double-
walled tank is to? - correct answers ✅pressurize the inner tank monitor the
pressure for one hour and then pressurize the space between the inner and
outer tanks with the air from the inner tank
when shipped a steel tank is covered with a coating that is an important part
of the tanks Corrosion Prevention system. "holidays" which show up in the
coating at the installation site should? - correct answers ✅should be
touched up with a compatible coating after proper surface preparation
touch up of holidays in a steel tank coatings at the installation site should be
done....... - correct answers ✅according to the manufacturer's instructions
dielectric bushings are usually made of what? - correct answers ✅non-
metallic material
factors to consider in determining the size shape and depth of a tank
excavation include what? - correct answers ✅*the tank manufacturers
recommendations
