Summary CISCO EQUIPMENT SPECIFICATION ON ETHERNET HUBS AND SWITCHES

HUB SPECIFICATION: Table D-1 System Specifications Description Specification Ports – Network device connectors (8) – Interconnect (2) (Micro 1502 and Micro Hub 1503 only) – Console port (1) (Micro Hub 1503 only) Connector Type – RJ-45 MDI-X shielded (Port 5 provides MDI-X or MDI options) – RJ-45 backplane bus – RJ-45 Access method CSMA/CD, 10 Mbps Media supported • 100-ohm unshielded twisted-pair (UTP) • 100-ohm shielded twisted-pair (STP) Indicator panel LEDs: • PWR—Indicates whether power is being supplied to hub • OK—Indicates whether self-test is successful • 1-8—Indicates port status: link, activity, partition, and disable • COL—Indicates network collisions • MGMT —(Micro Hub 1503 only) Indicates that hub is receiving SNMP data Configuration options • Direct connection to the CONSOLE port • Network connection via Telnet service • Network connection via optional SNMP management software Processor 80C31 (Micro Hub 1502) 386EX (Micro Hub 1503) Dimensions (H x W x D) 3.1 x 11.2 x 8.7 in. (7.85 x 28.4 x 22.1 cm) Height includes the stacking curves on top of the hub Weight 1.3 lb (0.6 kg) Power (external) 13.5 VDC (+/- 5%), 2A Nonoperating temperature -40 to 149°F (-20° to 65°C) Operating temperature 32 to 104°F (0° to 40°C) Operating humidity 10 to 85%, noncondensing Standards conformance IEEE 802.3 10BaseT Hub Stack – Expansion – Expansion interface – Configuration – Up to five units – Proprietary RJ-45 – Automatic hub-ID and bus termination (for stack) CABLE WRITING SPECIFICATIONS: Ethernet Cable Specifications You must supply the Ethernet cable for connecting workstations or other 10BaseT devices, such as compatible hubs or switches, to the Cisco Micro Hub. The Ethernet cable should meet the following specifications: • Straight-through Ethernet • 100-ohm Category 3, 4, or 5 • Can be shielded or unshielded • No longer than 328 feet (100 meters) If you are connecting another 10BaseT hub or switch, you can also run straight-through 10BaseT cabling from a a port labeled 1X through 8X on this hub to an MDI port on the other device. However, if you are connecting a Cisco Micro Hub workstation port (labeled 1X through 8X) to another hub's MDI-X port, you must use an Ethernet rollover cable. You can identify a rollover cable by comparing the modular ends of the cable. Holding the cable in your hand, side-by-side, with the tab at the back, the wire connected to the pin on the outside of the left connector (pin 1) is the same color as the pin on the outside of the right connector (pin 8). On Cisco cables, pin 1 is white on one connector, and pin 8 is white on the other connector. Cable Wiring This section contains wiring specifications for cables used with the Cisco Micro Hub, including the following: • 10BaseT port • Straight-through 10BaseT cable (RJ-45 to RJ-45) • Console cable and adapters Table D-2 8 Pin 1 Description 1 TX+ 2 TX- 3 RX+ 6 RX- 1Pins 4, 5, 7, and 8 are not used. 10BaseT Port Wiring Table D-3 describes the wiring for a straight-through 10BaseT cable, which is used to connect the hub to any devices that use a standard Ethernet LAN interface (for example, to a PC or server). Table D-3 RJ-45 Pin Signal Direction RJ-45 Pin 1 TX+ — 1 2 TX- — 2 3 RX+ — 3 4 - - 4 5 - - 5 6 RX- — 6 7 - - 7 8 - - 8 Straight-Through 10BaseT Cable (RJ-45 to RJ-45) A console cable kit is provided with your hub to connect a console (an ASCII terminal or PC running terminal emulation software) to the hub's CONSOLE port. The console cable kit contains: • RJ-45-to-RJ-45 console cable (light blue) • RJ-45-to-DB-25 adapter (light gray) • RJ-45-to-DB-9 adapter (light gray) describes the wiring for the CONSOLE port, the console cable, and both adapters. Table D-4 CONSOLE Port (DTE) RJ-45-to-RJ-45 Console Cable Signal RJ-45 Pin RJ-45 Pin DB-9 Pin DB-25 Pin Signal - 1 8 7 4 - DTR 2 7 4 20 DSR TxD 3 6 3 2 RxD GND 4 5 5 7 GND GND 5 4 5 7 GND RxD 6 3 2 3 TxD DSR 7 2 6 6 DTR - 8 1 8 5 - Console Cable and Adapter Pinouts Cisco 2500 Hub/Router Family Cisco 2505 Cisco 2507 Cisco 2516 8 Ethernet Ports 16 Ethernet Hub Ports 14 Ethernet Hub Ports 1 MDI/MDI-X Switch 2 Sync. Serial 2 Sync. Serial 2 Sync. Serial 1 ISDN BRI 1 Low-Speed Async. Serial 1 Low- Speed Async. Serial 1 Low-Speed Async. Serial 1 Console 1 Console 1 Console Hardware Specifications • Dimensions (height x width x depth): 1.75 x 17.5 x 10.6 in (4.44 x 44.45 x 28.62 cm) • Weight: 10 lb (4.5 kg) • Connectors: RJ-45 for 10BaseT (UTP), V.35, EIA/TIA-232, -449, -530, X.21 (Cisco 2505, 2507, 2516), RJ-45 for ISDN BRI (Cisco 2516) Environmental Specifications • Operating temperature range: 32° to 104° F (0° to 40° C) • Nonoperating temperature range: -40° to 185° F • (-40° to 85° C) • Power consumption: 40 watts max (135.5 Btu/hour) • Input: 100 to 240 VAC, universal, 1.0 amp @ 100V • Frequency at: 50 to 60 Hz • Agency Approvals: UL 1950, CSA 22.2 through 950, EN 60950, EN 41003, BABT, AUSTEL (AS3260, AST001), TÜV-GS mark, FCC Class A, VDE 0878 Part 3 and 30, Class B, CISPR 22 Class B, VCCI Class 2 (Japan), NFC 98020 (France), CE Mark (Europe), IEC 801-2, 3, 4, 5, 6 • Main Processor: MC 68030, 4 or 8 megabytes (MB) Flash memory1, 2, 4, or 6 MB DRAM* (expandable to 16 MB Flash, up to 18 MB DRAM) • Serial Interfaces: V.35, EIA 530, RS-232, RS-449, X.21, NRZ, NRZI, DTE or DCE (DTE only for EIA 530). Two high-speed serial interfaces. Compatible with leased lines, circuit-switched, and packet-switched services. Speeds up to 4 Mbps. • ISDN Interface (Cisco 2516 only): Basic Rate (2 B channels and 1 D channel) • Packet-Switched Interfaces: Frame Relay, X.25, X.25 DDN, SMDS LAN ACCESS SWITCHES: Cisco Catalyst 4500E Series Switch Data Sheet Figure 1. Cisco Catalyst 4500E Series The Cisco Catalyst 4500E Series extends control to the network edge with intelligent network services, including sophisticated quality of service (QoS), predictable performance, advanced security, comprehensive management, and integrated resiliency. Scalability of these intelligent network services is made possible with dedicated, specialized resources known as ternary content-addressable memory (TCAM). Ample TCAM resources (up to 384,000 entries) enable “high feature capacity”, which provides wire-speed routing and switching performance independent of provisioning of services such as QoS and security Table 1. Cisco Catalyst 4500E Series Chassis Features Feature Cisco Catalyst WS-C4503-E Chassis Cisco Catalyst WS C4506-E Chassis Cisco Catalyst WS C4507R+E Chassis Cisco Catalyst WS C4510R+E Chassis Total number of slots 3 6 7 10 Line-card slots 2 5 5 8 Supervisor engine slots 11 11 22 23 Dedicated supervisor engine slot numbers 1 1 3 and 4 5 and 6 Supervisor engine redundancy No No Yes Yes Supervisor Engines V-10GE, 6-E, 7-E, and 8-E) Supervisor engines supported Supervisor Engines 8-E, 8L-E, 7-E, 7L-E, 6-E, and 6L-E Supervisor Engines 8-E, 8L-E, 7-E, 7L-, 6-E, and 6L-E Supervisor Engines 8-E, 8L-E, 7-E, 7L-E, 6-E, and 6L-E Supervisor Engines 8-E, 7 E, and 6-E4 Maximum PoE per slot 1500W 1500W 1500W 1500W slots 1 and 2; 750W slots 3, 4, and 7-10 Bandwidth scalability per line-card slot Up to 48 Gbps on all slots Up to 48 Gbps on all slots Up to 48 Gbps on all slots5 Up to 48 Gbps on all slots5 Number of power supply bays 2 2 2 2 AC input power Yes Yes Yes Yes DC input power Yes Yes Yes Yes Integrated PoE Yes Yes Yes Yes Minimum number of power supplies 1 1 1 1 Power supplies supported ● 1000W AC ● 1400W AC ● 1300W ACV ● 2800W ACV ● 4200W ACV ● 6000W ACV ● 9000W ACV ● 1400W DC (triple input) ● 1400W-DC-P ● 1000W AC ● 1400W AC ● 1300W ACV ● 2800W ACV ● 4200W ACV ● 6000W ACV ● 9000W ACV ● 1400W DC (triple input) ● 1400W-DC-P ● 1000W AC ● 1400W AC ● 1300W ACV ● 2800W ACV ● 4200W ACV ● 6000W ACV ● 9000W ACV ● 1400W DC (triple input) ● 1400W-DC-P ● 1400W AC ● 2800W ACV ● 4200W ACV ● 6000W ACV ● 9000W ACV ● 1400W DC (triple input) ● 1400W-DC-P Number of fan-tray bays 1 1 1 1 Location of 19-inch rack-mount Front Front Front Front Location of 23-inch rack-mount Front (option) Front (option) Front (option) Front (option) 1 Slot 1 is reserved for supervisor engine only; slots 2 and higher are reserved for line cards. 2 Slots 3 and 4 are reserved for supervisor engines only in Cisco Catalyst 4507R+E; slots 1-2 and 5-7 are reserved for line cards. 3 Slots 5 and 6 are reserved for supervisor engines only in Cisco Catalyst 4510R+E; slots 1-4 and 7-10 are reserved for line cards. 4 6 Gbps only on slots 8-10. 5 WS-C4507R+E and WS-C4510R+E chassis support up to 24 Gbps per line-card slot when used with Supervisor Engine 6-E. Configuration Alternatives The Cisco Catalyst 4500 Series offers a powerful and flexible network solution that can be built with eight supervisor engine alternatives. Each provides a high-performance, centralized, shared-memory switch fabric, protecting your line-card investment by supporting the addition of optional higher layer engines (Table 2). Table 2. Cisco Catalyst 4500E Series Supervisor Engine Support Feature Cisco Catalyst 4500 Series Supervisor Engine 6L-E Cisco Catalyst 4500 Series Supervisor Engine 6-E Cisco Catalyst 4500 Series Supervisor Engine 8-E, 7-E Cisco Catalyst 4500 Series Supervisor Engine 8L-E, 7L-E Cisco Catalyst WS C4503-E chassis 24 Gbps/slot 24 Gbps/slot 48 Gbps/slot 48 Gbps/slot Cisco Catalyst WS C4506-E chassis 24 Gbps/slot 24 Gbps/slot 48 Gbps/slot 48 Gbps/slot Cisco Catalyst WS C4507R+E chassis 24 Gbps/slot 24 Gbps/slot 48 Gbps/slot 48 Gbps/slot Cisco Catalyst WS C4510R+E chassis Not supported 24 Gbps/slot (slot 1-7) 6 Gbps/slot (slot 8-10) 48 Gbps/slot Not supported The Cisco Catalyst 4500 Series has flexible interface types and port densities that allow you to mix and match network configurations to meet the specific needs of campus networks (Table 3). Table 3. Cisco Catalyst 4500 Series Port Densities Cisco Catalyst 4500 Series Switching Modules Number of Interfaces Supported per Line Card Cisco Catalyst 4503-E Cisco Catalyst 4506-E Cisco Catalyst 4507R+E Cisco Catalyst 4510R+E Switched 10/100 Fast Ethernet (RJ 45) 48 96 240 240 384 Switched 10/100 Fast Ethernet (RJ+45) with IEEE 802.3af at Power over Ethernet (PoE/PoE+) 48 96 240 240 384 Switched 100 FX Fast Ethernet (MT RJ) 48 96 240 240 384 Switched 1000BASE-X (fiber) 6, 18, or 48 100 244 244 388 Switched 10/100/1000BASE-T Gigabit Ethernet 48 96 240 240 384 Switched 10/100/1000BASE-T Gigabit Ethernet with IEEE 802.3af at PoE/PoE+ 48 96 240 240 384 Switched 10/100/1000BASE-T Gigabit Ethernet with UPOE 48 96 240 240 384 Switched 10 Gigabit Ethernet 6 or 12 32 68 686 104 Configuration Flexibility and Modular Superiority You can mix and match Cisco Catalyst 4500 Series Line Cards to suit numerous LAN access, server connectivity, small and medium-sized business (SMB), or branch-office deployments. The Cisco Catalyst 4500 Series supports the line cards listed in Table 4 by part number. Table 4. Cisco Catalyst 4500 Series Line Cards Product Number Description Cisco Catalyst 4500E Series Line Cards WS-X4748-12X48U+E Cisco Catalyst 4500E 48-Port UPOE w/ 12-Port MultiGigabit and 36-Port 10/100/1000 WS-X4748-UPOE+E Cisco Catalyst 4500E Series 48-Port UPOE 10/100/1000 (RJ-45) WS-X4748-RJ45V+E Cisco Catalyst 4500E Series 48-Port 802.3at PoEP 10/100/1000 (RJ-45) WS-X4748-RJ45-E Cisco Catalyst 4500E Series 48-Port 10/100/1000 (RJ-45) WS-X4712-SFP+E Cisco Catalyst 4500E Series 12-port 10 Gigabit Ethernet (SFP+) WS-X4748-SFP-E Cisco Catalyst 4500E Series 48-Port GE (SFP) WS-X4724-SFP-E Cisco Catalyst 4500E Series 24-Port GE (SFP) WS-X4712-SFP-E Cisco Catalyst 4500E Series 12-Port GE (SFP) WS-X4624-SFP-E Cisco Catalyst 4500E Series 24-port GE (SFP) WS-X4612-SFP-E Cisco Catalyst 4500E Series 12-port GE (SFP) WS-X4648-RJ45V-E Cisco Catalyst 4500E Series 48-Port PoE 10/100/1000(RJ45) WS-X4648-RJ45V+E Cisco Catalyst 4500E Series 48-Port Premium PoE 10/100/1000(RJ45) WS-X4606-X2-E Cisco Catalyst 4500E Series 6-Port 10GE (X2) WS-X4648-RJ45-E Cisco Catalyst 4500E Series 48-Port Data 10/100/1000(RJ45) Cisco Catalyst 4500 Classic 10/100 Line Cards WS-X4148-RJ Cisco Catalyst 4500 10/100 Auto Module, 48-Port (RJ-45) WS-X4248-RJ45V Cisco Catalyst 4500 PoE 802.3af 10/100 48-Port (RJ-45) Cisco Catalyst 4500 Classic 10/100/1000 Line Cards WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-RJ45V+ Cisco Catalyst 4500 48-Port 802.3af PoE and 802.3at PoEP 10/100/1000 (RJ-45) WS-X4548-GB-RJ45V Cisco Catalyst 4500 PoE IEEE 802.3af 10/100/1000, 48 Ports (RJ-45) Cisco Catalyst 4500 Classic 100 BASE-X FE Line Cards WS-X4148-FX-MT Cisco Catalyst 4500 Series 48-Port 100BASE-FX Fast Ethernet Line Card (MT-RJ) for multimode fiber WS-X4248-FE-SFP Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-Port 100BASE-X (SFP) Cisco Catalyst 4500 Classic 1000 BASE-X GE Line Cards WS-X4506-GB-T Cisco Catalyst 4500 6-Port 10/100/1000 RJ-45 PoE IEEE 802.3af and 1000BASE-X (SFP) WS-X4418-GB Cisco Catalyst 4500 Gigabit Ethernet Module, Server Switching 18 Ports (GBIC) WS-X4448-GB-SFP Cisco Catalyst 4500 Gigabit Ethernet Module, 48 Ports 1000X (SFP) Table 5 lists the minimum software requirements for the Cisco Catalyst 4500 supervisor engines. Table 5. Cisco Catalyst Supervisor Engine Software Minimum Requirements Chassis Supervisor Engine Minimum Software Requirement Cisco WS-C4503-E and WS-C4506-E Supervisor Engine 6-E Supervisor Engine 6L-E Supervisor Engine 7-E Supervisor Engine 7L-E Supervisor Engine 8-E Supervisor Engine 8L-E Cisco IOS® Software Release 12.2(40)SG Cisco IOS Software Release 12.2(52)SG Cisco IOS XE Software Release 3.0(1)SG Cisco IOS XE Software Release 3.2.0XO Cisco IOS XE Software Release 3.3.0XO Cisco IOS XE Software Release 3.8.1E Cisco WS-C4507R+E Supervisor Engine 6-E Supervisor Engine 6L-E Supervisor Engine 7-E Supervisor Engine 7L-E Supervisor Engine 8-E Supervisor Engine 8L-E Cisco IOS Software Release 12.2(54)SG Cisco IOS Software Release 12.2(54)SG Cisco IOS XE Software Release 3.0(1)SG Cisco IOS XE Software Release 3.2.0XO Cisco IOS XE Software Release 3.3.0XO Cisco IOS XE Software Release 3.8.1E Cisco WS-C4510R+E Supervisor Engine 6-E Supervisor Engine 7-E Supervisor Engine 8-E Cisco IOS Software Release 12.2(54)SG Cisco IOS XE Software Release 3.0(1)SG Cisco IOS XE Software Release 3.3.0XO Physical Specifications Table 6 lists physical specifications. Table 6. Physical Specifications of Cisco Catalyst 4500 Series Chassis Specification WS-C4503-E WS-C4506-E WS-C4507R+E WS-C4510R+E Dimensions (H x W x D) 12.25 x 17.31 x 12.50 in. (31.12 x 43.97 x 31.70 cm) 17.38 x 17.31 x 12.50 in. (44.13 x 43.97 x 31.70 cm) 19.19 x 17.31 x 12.50 in. (48.74 x 43.97 x 31.70 cm) 24.35 x 17.31 x 12.50 in. (61.84 x 43.97 x 31.70 cm) Rack units (RU) 7RU 10RU 11RU 14RU Chassis weight (with fan tray) 32.25 lb (14.63 kg) 40.50 lb (18.37 kg) 44.50 lb (20.19 kg) 54.50 lb (24.73 kg) Mounting 19- and 23-in. rack compatible (19-in. rack and cable guide hardware included) 19- and 23-in. rack compatible (19-in. rack and cable guide hardware included) 19- and 23-in. rack compatible (19-in. rack and cable guide hardware included) 19- and 23-in. rack compatible (19-in. rack and cable guide hardware included) Power Supply Indicators and Interfaces ● Output Fail LED (per unit): RED ● Input OK LED(per input): Green ● Fan OK LED(per input): Green Tables 7 and 8 describe power supply specification. Table 7. Cisco Catalyst 4500E Series Power Supply Specifications (Data Only) Power Supply 1000W AC 1400W AC 1400W DC Triple Input Integrated PoE No (data only) No (data only) No (data only) Input current (rated) 12A at 100 VAC, 5A at 240 VAC 16A at 100 VAC, 7A at 240 VAC Two -48 VDC at 15A; One -48 VDC at 12.5A Output current (data) ● 12V at 83.4A ● 3.3V at 12.2A ● 12V at 113.4A ● 3.3V at 12.2A ● 12V at 1360W ● 3.3V at 40W Output power redundant mode (data) 1000W + 40W 1360W + 40W 1400W + 40W Output power combined mode (data) 1667W 2473W - Heat dissipation 943 BTU per hour 1048 BTU per hour 1048 BTU per hour Holdup time 20 ms 20 ms 8 ms Hot-swappable Yes Yes Yes Table 8. Cisco Catalyst 4500E Series Power Supply Specifications (Data and PoE) Power Supply 1300W AC 2800W AC 4200W AC 6000 AC 9000 AC 1400W DC with Power Entry Module (PEM) Integrated PoE Yes (up to 800W) Yes (up to 1400W) Yes (up to 3855W) Yes (up to 4800W) Yes (up to 7500W) Up to 7500W (minus the power consumed for data) when connected directly to a DC power plant or 2 external AC power shelves Input current (rated) ● 16A at 100 VAC ● 7A at 240 VAC ● 16A at 200 VAC ● Two 12A at 100 VAC Or ● Two 12A at 200 VAC ● Two 12A at 100 VAC Or ● Two 16A at 200 VAC ● Three 12A at 100 VAC Or ● Three 16A at 200 VAC ● 31A at -60 VDC (data only) ● 180A at -48 VDC (PoE) Output current (data) ● 12V at 84.7A ● 3.3V at 12.5A ● 12V at 113.3A ● 3.3V at 12.5A ● 12V at 115.3A ● 3.3V at 12.5A ● 12V at 186.9A ● 3.3V at 12.5A ● 12V at 163.3A ● 3.3V at 12.5A ● 12V at 120A ● 3.3V at 12.5A Output current (PoE) -50V at 16.7A -50V at 28A -50V at 77.1A (200V) -50V at 38A (100V) -50V at 100.0A (200V) -50V at 38.5A (120V) -50V at 150.0A (200V) -50V at 50.0A (120V) 140A at -48/-60 VDC Output power redundant mode (data) 1000W + 40W 1360W + 40W 1383W + 40W 2200W + 40W 1960W + 40W 1360W + 40W Output power redundant mode (PoE) 800W maximum per power supply 1400W maximum per power supply ● 3700W (220V) ● 1850W (110V) ● 4800W (220V) ● 1850W (110V) ● 7500W (220V) ● 2500W (110V) Up to 7500W (minus the power consumed for data) Output power combined mode (data) 1667W 2473W 2766W 4400W 3920W - Output power combined mode (PoE) 1333W 2333W 6700W (220V) 3360W (110V) 8700W (220V) 3360W (110V) 14,400W (220V) 4150W (110V) 3800W (100V) Heat dissipation 1568 BTU/hr 2387 BTU/hr 3580 BTU/hr 2720 BTU/hr 3010 BTU/hr Data only: 1591 BTUs per hour Data and voice: 2905 BTUs per hour Holdup time 20 ms 20 ms 20 ms 20 ms 20 ms 4 ms Hot swappable Yes Yes Yes Yes Yes Yes Cisco Catalyst 3850 Series Switch Data Sheet Switch Models and Configurations All switches ship with one of the five power supplies (350WAC, 715WAC, 750WAC, 1100WAC, or 440WDC)[5]. Figures 1 through 3 show the Cisco Catalyst 3850 Series Switches. Figure 1. Cisco Catalyst 3850 Series Switches