Tattoo Oregon Exam Questions With 100% Correct Answers Latest Updated 2024 (GRADED)

Tattoo Oregon Exam Questions With 100% Correct Answers Latest Updated 2024 (GRADED) more leverage - Answer- an a-bar extending past rear coil creates _________ 1.5-1.625 - Answer- usually a longer armature bar is a range from _.___ to _.____ plain steel, no chrome - Answer- armature bars should be _________ ________, _____ ____________ .010-.012 - Answer- when a-bar is flat on coil, rear coil has between .___-.___ dust, lint, debris, hitting at an angle - Answer- what can cause a rattle or deflection of abar? (4 things) run hot - Answer- coils with too much core showing tend to ____ _____ buzz or rattle - Answer- do not allow the front spring to hang over the rear of the armature bar because it can create a ______ or ___________ contact screws - Answer- there should be no sharp edges on __________ _______, should be rounded and very smooth faster - Answer- a short front spring will be _________ rockwell scale - Answer- all metals are measured on the _________ _______ 48-51 - Answer- best on the scale for spring stock is ___-___ alcohol - Answer- can be used to clean your contact area and screws and spring rattle - Answer- thin, cheap binding posts cause ________ leverage - Answer- _____________ is a key factor when it comes to a-bar choice 100 - Answer- copper is ___% conductive copper and zinc - Answer- brass is a mixture of 6-32, 8-32 - Answer- some machines have _-__ threaded machine screws and some have _-__ Tattoo Oregon Exam Questions With Correct Answers Latest 2023/2023 (Graded) thicker binding posts - Answer- _________ __________ ______ help dampen vibrations shorter - Answer- is a shorter or longer front spring better on a liner? shoulder washers - Answer- screw insulators commonly known as __________ __________ , most common are made of fiber and plastic true - Answer- a longer A-Bar has more leverage, true or false? electrical contact to contact screw - Answer- purpose of the binding post rubber grommets - Answer- dampener or rubber grommets better? hot - Answer- never use brass screws or any other non-ferrous screws for the coil screws can cause the coils to get ___ soldering lugs - Answer- ______________ ____ are soldered at the ends of the coil wires and capacitor wires, with a 5/16" tube vise liners - Answer- tattoo machine capacitors have 22 MFD for ________ shaders - Answer- tattoo machine capacitors have 47 MFD for _________ faster - Answer- the lower the MFD rating the ________ the machine will run frame - Answer- which parts job is to simply "hold" the circuits in place 3 - Answer- how many circuits when you look at the machine unit? 12 - Answer- most machines run well under __ volts 25 - Answer- how many volts for 47 MFD? coils - Answer- the "heart and brains" of the tattoo machine 5/16, 3/8 - Answer- standard coils are 1.25 inches tall and vary in diameter but most common are _/__ and _/_ coils - Answer- if you have a noisy machine and can't find a reason check the _____ skin scribe - Answer- a special marker for drawing on skin freehand capacitor - Answer- a device used to store an electric charge, consisting of one or more pairs of conductors separated by an insulator. coils - Answer- when power is delivered to these an electromagnetic field is created. the field draws down the metal armature bar, hovering above these forcing the tattoo needles down, out of your tube and into your clients skin contact screw - Answer- stationary contact point for the front spring front spring - Answer- this is the part that is in constant contact with the contact screw, made of steel, longer for shaders and shorter for liners back spring - Answer- attached to the frame, front spring and armature bar, provides up and down motion of the needles rear binding post - Answer- this fixes the coils to the clipboard power that is coming from the power supply. is also attached to the top of the side to hold the contact screw top hat grommet - Answer- part that helps the needle to be steady on the a-bar tube clamp - Answer- to keep the tubes or tips on yoke - Answer- regulates the height of the coils armature bar - Answer- steel mass for the magnetic pull rotary tattoo machine - Answer- contains a small motor encased in the tattoo machine itself which moves the attached needles up and down consistently without a break in the circuit thermafax paper - Answer- used to create stencils that are applied to the skin prior to tattoo foot switch - Answer- turns the power supply on or off allowing the artist to control the tattoo machine with their foot clip cord - Answer- cable used to connect a tattoo machine to the tattoo machines power supply cartridge needles - Answer- has the needles molded into a plastic bar and is encased in a cartridge tube - Answer- plastic disposable that connects to the needle bar 360 - Answer- total hours of tattoo instruction 210 - Answer- how many hours of theory total for tattoo 150 - Answer- how many hours of practical tattooing 50 - Answer- total minimum of tattoo procedures to be completed 20 - Answer- hours of theory for needles and needle bars 20 - Answer- hours of theory for tattoo machines 20 - Answer- hours of theory for equipment and supplies 40 - Answer- hours of theory for safety and infection control 10 - Answer- hours of theory for color theory and pigments 10 - Answer- hours of theory for design, art and placement 20 - Answer- hours of theory for skin 20 - Answer- hours of theory for client services 20 - Answer- hours of theory for business operations 20 - Answer- hours of theory for oregon laws and rules 10 - Answer- hours of theory discretionary 10 procedures - Answer- one teacher to one student must directly supervise a minimum of the first __ ______________ to be preformed in no less than 30 days 40 procedures - Answer- one teacher to four students may be indirectly supervised on the last __ ____________ 7 - Answer- the board of body art practitioners consist of how many members? 2 - Answer- how many licensed body piercers on state board 2 - Answer- how many licensed tattoo artists on state board 1 - Answer- how many licensed to preform electrolysis on state board 1 - Answer- how many public members on state board 1 - Answer- how many health care providers on state board 4 years - Answer- term of office for each member of the state board affidavit of licensure - Answer- An original document or other approved means of verifying licensure history, including information disclosing all unresolved or outstanding penalties and/or disciplinary actions. EPA - Answer- Environmental Protection Agency An independent federal agency established to coordinate programs aimed at reducing pollution and protecting the environment FDA - Answer- Food and Drug Administration. The agency that is responsible for determining if a food or drug is safe and effective enough to be sold to the public. high-level disinfectant - Answer- A chemical agent, which has demonstrated tuberculocidal activity and is registered with the EPA instruments - Answer- means equipment used during tattooing services. Types of instruments include but are not limited to needles and tubes office - Answer- health licensing office