Elevator Test/65 Questions and
Answers with 100% Correct
Solutions/Latest Update 2023-
2024
Convert 12,540 lbs to Kg? - -Lbs/2.204 .... 12,.204
5,689 kg
-You are working on an elevator installation job with your mechanic.
What type of detailed drawings are you likely to encounter? - -
Standardized
electrical
Hoistway
Structure
-You are assisting a mechanic installing upper hoist way limit switches,
which drawings will he need? - -Standardized detailed drawings found in
the job folder
-Mechanic is installing a lifeline in the hoist way. Which location should
it be installed? - -Where you can access it
-Convert 6 inches to millimeters? - -1" = 25.4mm 6" * 25.4mm
152.4mm
-Working drawings that were approved by the building owner are
labeled with which term? - -Final
-Door lock picture, Which letter illustrates dimension lines? - -Answer
not available
-In a standard orthographic drawing, where is the placement of back
view if needed? - -Located off to one side of the working drawing and it
is clearly labeled
-There are several standard drawing methods showing 3 sides of an
object at once. What is it called? - -Isometric
-How would you describe a class 3 fit for shaft and boar diameters? - -
Snuggest positive allowance
-Which class of bolt threads provides the highest level of precision? - -
Class 3
, -What is the difference between us standard and metric standard
threads? - -Metric is measured by the number of pitch vs the number of
threads
-What tool do you need to remove an internal snap ring? - -Snap Ring
Pliers
-Convert 33.5 inches to millimeters? - -1" = 25.4mm 33.5 * 25.4
850.9mm
-What type of drawing presents a 3-sided view of an object? - -
Orthographic
-Question not available - -3 boxes
-4730/144 - -32.84
-When erecting a scaffold what type of fall protection can be used in
addition to a fall arrest system? - -Guard Rails
-What type of scaffold hazards are the most serious? - -Unsafe access &
Collapse
-What mnemonic can be used to remember the 5 most serious scaffold
hazards? - -Fuses
-You are the only subcontractor on the job site, when erecting the
scaffold who serves as the safety officer? - -Scaffolder
-Your employer is looking for someone who has experience and has
authority knowledge to take prompt corrective measures to eliminate
hazards. Who is this person? - -Competent person
-To keep a rolling scaffold from racking, what must be installed? - -
Horizontal diagonal braces
-Of the following which term describe 2 point suspended scaffold used
by elevator constructors? - -Swing Stage or powered platform
-Find the running clearance from the car sill to hoist way sill? Use 180
print 2 - -1 ¼"
-What is the distance from the center rails to the back of the hoist way?
- -2' 6 3/8"
-What is the distance from the pit floor to the center of the oil line? - -1'
5" ¾
-What is the distance from the pit floor to the top of the jack? - -1'11"
1/4
Answers with 100% Correct
Solutions/Latest Update 2023-
2024
Convert 12,540 lbs to Kg? - -Lbs/2.204 .... 12,.204
5,689 kg
-You are working on an elevator installation job with your mechanic.
What type of detailed drawings are you likely to encounter? - -
Standardized
electrical
Hoistway
Structure
-You are assisting a mechanic installing upper hoist way limit switches,
which drawings will he need? - -Standardized detailed drawings found in
the job folder
-Mechanic is installing a lifeline in the hoist way. Which location should
it be installed? - -Where you can access it
-Convert 6 inches to millimeters? - -1" = 25.4mm 6" * 25.4mm
152.4mm
-Working drawings that were approved by the building owner are
labeled with which term? - -Final
-Door lock picture, Which letter illustrates dimension lines? - -Answer
not available
-In a standard orthographic drawing, where is the placement of back
view if needed? - -Located off to one side of the working drawing and it
is clearly labeled
-There are several standard drawing methods showing 3 sides of an
object at once. What is it called? - -Isometric
-How would you describe a class 3 fit for shaft and boar diameters? - -
Snuggest positive allowance
-Which class of bolt threads provides the highest level of precision? - -
Class 3
, -What is the difference between us standard and metric standard
threads? - -Metric is measured by the number of pitch vs the number of
threads
-What tool do you need to remove an internal snap ring? - -Snap Ring
Pliers
-Convert 33.5 inches to millimeters? - -1" = 25.4mm 33.5 * 25.4
850.9mm
-What type of drawing presents a 3-sided view of an object? - -
Orthographic
-Question not available - -3 boxes
-4730/144 - -32.84
-When erecting a scaffold what type of fall protection can be used in
addition to a fall arrest system? - -Guard Rails
-What type of scaffold hazards are the most serious? - -Unsafe access &
Collapse
-What mnemonic can be used to remember the 5 most serious scaffold
hazards? - -Fuses
-You are the only subcontractor on the job site, when erecting the
scaffold who serves as the safety officer? - -Scaffolder
-Your employer is looking for someone who has experience and has
authority knowledge to take prompt corrective measures to eliminate
hazards. Who is this person? - -Competent person
-To keep a rolling scaffold from racking, what must be installed? - -
Horizontal diagonal braces
-Of the following which term describe 2 point suspended scaffold used
by elevator constructors? - -Swing Stage or powered platform
-Find the running clearance from the car sill to hoist way sill? Use 180
print 2 - -1 ¼"
-What is the distance from the center rails to the back of the hoist way?
- -2' 6 3/8"
-What is the distance from the pit floor to the center of the oil line? - -1'
5" ¾
-What is the distance from the pit floor to the top of the jack? - -1'11"
1/4
