Testout Network Pro Exam Questions
and Answers
You manage a network with a single switch. On each switch port, a hub connects
multiple devices to the switch.
which condition are you most likely to experience on the network ? - Answer- collisions
select the statement that best describes a broadcast storm. - Answer- A Broadcast
storm occurs when there are so many broadcast messages on the network that they
approach or exceed the network bandwidth..
Which of the following solutions would you implement to eliminate switching loops? -
Answer- spanning tree
You manage a network that uses a single switch. All ports within your buildings connect
through he single switch . Which feature should you implement? - Answer- VLANs
You manage a network that uses multiple switches. You want to provide multiple paths
between switches so that if one link goes down, an alternate path is available.
Which feature should your switch support? - Answer- spanning tree
You run a small network for your business that has a single router connected to the
internet and a single switch. You keep sensitive doc.
What should you use for this situation? - Answer- VLAN
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature prevents switching loops and ensures there is only a single active patch
between any two switches? - Answer- Spanning tree
Which feature prevents switching loops and ensures there is only a single active path
between any two switches? - Answer- spanning trees
A user reports that network access from her workstation is very slow. The problem does
not seem to be affecting any other users.
Which of the following conditions is the most likely cause? - Answer- Duplex mismatch
,You manage a local area network with several switches. A new employee has started
today so you connect her workstation to a switch port.
Which of the following is the most likely cause of the problem? - Answer- Incorrect
VLAN assignment
You manage a network with multiple switches. You find that your switches are
experiencing heavy broadcast storms.
Which of the following will help reduce the effects of a broadcast storm? - Answer-
Enable spanning tree on the switches
Which of the following solutions would you implement to eliminate switching loops? -
Answer- spanning tree
While viewing the status of the interfaces on a Cisco switch, you see abnormally large
of oversized ethernet frames being received on one interface. This interface is
connected to a workstation located on the 2nd floor.
What could be causing this to happen? - Answer- The workstation's network board is
jabbering
The network board in a workstation is currently configured as follows: - Answer- show
running-config interface
show interface
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature allows the switches to pass VLAN traffic between the switches? -
Answer- Trunking
You manage a network with two switches. The switches are connected together through
their Gigabit Ethernet uplink ports.
You define VLAN 1 and VLAN 2 on each switch. A device on the first switch in VLAN 1
needs to communicate with a device on the second switch also in VLAN 1.
What should you configure to allow communication between these two devices through
the switches? - Answer- Trunking
When configuring VLANs on a switch, what type of switch ports are members of all
VLANs defined on the switch? - Answer- Trunk Ports
Computers A and B are on the same VLAN and are separated by two switches, as
shown in the exhibit. Computer A sends a Fram to Computer B.
Which of the following best describes the composition of the frame as it travels from A
to B? - Answer- Computer A sends a normal frame. The first switch appends a VLAN ID
, to the frame. The second switch removes the VLAN ID before forwarding it to Computer
B.
Which of the following statements accurately describes a VLAN ID? - Answer- Switches
append a VLAN ID to the header of each frame to identify the virtual network to which it
belongs.
CSMA/CD - Answer- The media access control method of all Ethernet networks is
___________________.
The device listens to determine if the transmission media is free. - Answer- A network is
connected following the IEEE 802.3 specifications. Which of the following best
describes when a device can transmit messages?
10BaseT & 1000BaseT - Answer- Which of the following use the CSMA/CD access
method? Select all that apply.
Bus and Star - Answer- Which of the following physical topologies are used with
Ethernet networks? (Select two.)
Fiber optic - Answer- Ethernet 100BaseFX networks use what type of cabling?
100BaseFX & 1000BaseLX - Answer- Which of the following Ethernet standards uses
fiber optic cabling? (Select two.)
100 meters - Answer- Your network follows the 100BaseTx specifications for Fast
Ethernet. What is the maximum cable segment length allowed?
100 meters - Answer- With an Ethernet 10BaseT network, the maximum cable length
between a computer and the hub is __________.
10BaseSR &1000BaseSX - Answer- You have been tasked with designing an Ethernet
network. Your client needs to implement a very high-speed network backbone between
campus buildings; some of which are around 300 meters apart. Multimode fiber-optic
cabling has already been installed between buildings. Your client has asked that you
use the existing cabling.
Which Ethernet standard meets these guidelines? (Choose two.)
Type 1A STP or Category 5 UTP - Answer- What type of cabling is used with
100BaseTX Fast Ethernet networks?
Physical star/logical bus & Physical star/logical star - Answer- What topology is used
with 100BaseTX Fast Ethernet networks? (Select two.)
and Answers
You manage a network with a single switch. On each switch port, a hub connects
multiple devices to the switch.
which condition are you most likely to experience on the network ? - Answer- collisions
select the statement that best describes a broadcast storm. - Answer- A Broadcast
storm occurs when there are so many broadcast messages on the network that they
approach or exceed the network bandwidth..
Which of the following solutions would you implement to eliminate switching loops? -
Answer- spanning tree
You manage a network that uses a single switch. All ports within your buildings connect
through he single switch . Which feature should you implement? - Answer- VLANs
You manage a network that uses multiple switches. You want to provide multiple paths
between switches so that if one link goes down, an alternate path is available.
Which feature should your switch support? - Answer- spanning tree
You run a small network for your business that has a single router connected to the
internet and a single switch. You keep sensitive doc.
What should you use for this situation? - Answer- VLAN
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature prevents switching loops and ensures there is only a single active patch
between any two switches? - Answer- Spanning tree
Which feature prevents switching loops and ensures there is only a single active path
between any two switches? - Answer- spanning trees
A user reports that network access from her workstation is very slow. The problem does
not seem to be affecting any other users.
Which of the following conditions is the most likely cause? - Answer- Duplex mismatch
,You manage a local area network with several switches. A new employee has started
today so you connect her workstation to a switch port.
Which of the following is the most likely cause of the problem? - Answer- Incorrect
VLAN assignment
You manage a network with multiple switches. You find that your switches are
experiencing heavy broadcast storms.
Which of the following will help reduce the effects of a broadcast storm? - Answer-
Enable spanning tree on the switches
Which of the following solutions would you implement to eliminate switching loops? -
Answer- spanning tree
While viewing the status of the interfaces on a Cisco switch, you see abnormally large
of oversized ethernet frames being received on one interface. This interface is
connected to a workstation located on the 2nd floor.
What could be causing this to happen? - Answer- The workstation's network board is
jabbering
The network board in a workstation is currently configured as follows: - Answer- show
running-config interface
show interface
You manage a single subnet with three switches. The switches are connected to
provide redundant paths between the switches.
Which feature allows the switches to pass VLAN traffic between the switches? -
Answer- Trunking
You manage a network with two switches. The switches are connected together through
their Gigabit Ethernet uplink ports.
You define VLAN 1 and VLAN 2 on each switch. A device on the first switch in VLAN 1
needs to communicate with a device on the second switch also in VLAN 1.
What should you configure to allow communication between these two devices through
the switches? - Answer- Trunking
When configuring VLANs on a switch, what type of switch ports are members of all
VLANs defined on the switch? - Answer- Trunk Ports
Computers A and B are on the same VLAN and are separated by two switches, as
shown in the exhibit. Computer A sends a Fram to Computer B.
Which of the following best describes the composition of the frame as it travels from A
to B? - Answer- Computer A sends a normal frame. The first switch appends a VLAN ID
, to the frame. The second switch removes the VLAN ID before forwarding it to Computer
B.
Which of the following statements accurately describes a VLAN ID? - Answer- Switches
append a VLAN ID to the header of each frame to identify the virtual network to which it
belongs.
CSMA/CD - Answer- The media access control method of all Ethernet networks is
___________________.
The device listens to determine if the transmission media is free. - Answer- A network is
connected following the IEEE 802.3 specifications. Which of the following best
describes when a device can transmit messages?
10BaseT & 1000BaseT - Answer- Which of the following use the CSMA/CD access
method? Select all that apply.
Bus and Star - Answer- Which of the following physical topologies are used with
Ethernet networks? (Select two.)
Fiber optic - Answer- Ethernet 100BaseFX networks use what type of cabling?
100BaseFX & 1000BaseLX - Answer- Which of the following Ethernet standards uses
fiber optic cabling? (Select two.)
100 meters - Answer- Your network follows the 100BaseTx specifications for Fast
Ethernet. What is the maximum cable segment length allowed?
100 meters - Answer- With an Ethernet 10BaseT network, the maximum cable length
between a computer and the hub is __________.
10BaseSR &1000BaseSX - Answer- You have been tasked with designing an Ethernet
network. Your client needs to implement a very high-speed network backbone between
campus buildings; some of which are around 300 meters apart. Multimode fiber-optic
cabling has already been installed between buildings. Your client has asked that you
use the existing cabling.
Which Ethernet standard meets these guidelines? (Choose two.)
Type 1A STP or Category 5 UTP - Answer- What type of cabling is used with
100BaseTX Fast Ethernet networks?
Physical star/logical bus & Physical star/logical star - Answer- What topology is used
with 100BaseTX Fast Ethernet networks? (Select two.)
