BECC MOD 1 TEST ACTUAL QUESTIONS AND
ANSWERS 2024 GRADED A+
What ARE 3 considerations when dealing with electrical burns?
Electrical current may burn a large area just below the surface
Perform CPR if needed
Treatment is the same as for a thermal burn
(True/False) Section 300 of the PQS book list infrequent task and abnormal
conditions.
TRUE
The overall purpose of PQS is to ......
provide a means to qualify ships personnel.
(True/False) PQS provides an effective way to monitor an individual's
qualification progress.
TRUE
When can your Final Qualification Page be signed?.
After all line items have been completed and signed
Vocabulary used in each qualification can be found in the ....... Section of the
PQS book.
FUNDAMENTALS
Progress and completed qualifications of each person in the division are
displayed on/in the .......
PROGRESS CHART
Who is the final qualification authority?
COMMANDING OFFICER
A five inch outside micrometer will measure objects that are ....... inches thick.
4-5IN
A Dial indicator may be used to.......
ALIGN MACHINERY
It is NOT safe to operate electrical power tools in areas where ....... is/are
present.
FLAMMABLE GASES
Electrical power tools must be inspected prior to issue by a qualified .......
ELECTRICIAN
A torque wrench is used to measure the tightness of ...
FASTENERS
Torque wrenches are considered ....... equipment
PRECISION
If a maintenance procedure does not specify a torque sequence, utilize the
recommended sequence found in .......
NTM CHAPER 075
Which document contains maintenance requirements pertaining to all
equipment in a command?
PMS MASTER FILE
16. Which portion of the PMS Master File provides the work center supervisor
a ready reference of planned maintenance requirements.?
WORK CENTER PMS MANUAL
, If a planned maintenance action cannot be completed in accordance with the
steps listed on the MRC, the maintenance man should .......
STOP AND REPORT TO THE WCS
What is used to notify personnel that death or injury may result if the operating
procedures and practices are NOT correctly followed?
Warnings
Which of the following serves as the "Table of Contents" for the Work Center
PMS manual?
LIST OF EFFECTIVE PAGES (LOEP)
The SYSCOM Control Number assigned for each maintenance requirement
listed in a MIP must match the number on the corresponding
MRC (maintenance requirement card)
Materials needed to perform the required maintenance are found on the
FRONT OF THE MRC
The responsibility to replace a missing MRC belongs to the .......
WORK CENTER SUPERVISOR
Who assists the Department Head in managing maintenance at the division
level?
DIVISION OFFICER
Who has the responsibility to maintain the list of effective pages?
WORK CENTER SUPERVISOR
Which schedule is NOT used in the 3M system?
DAILY
Which of the following periodicity code is used when a maintenance
requirement is performed monthly?
M
Which document is use to verify that you have the proper MRC?
MIP (MAINTENANCE INDEX PAGE)
You must check the ...... to ensure that the weekly schedule is correct.
QUARTELY SCHEDULE
Material needed to perform a specific PMS action is listed on the ......
MRC (MAINTENANCE REQUIREMENT CARD)
The maintenance procedure steps on the MRC are
TO BE FOLLOWED PRECISELY
The shipboard hazardous material list is provided ...... on the Department of
Defense's CDROM.
QUARTERLY
Requirements for storage of hazardous material are found on the ......
MSDS
While grinding or chiseling, what should be used to protect the eyes?
CHIPPING GOGGLES
Which procedure does NOT require eye protection?
NORMAL OPERATION OF A LUBE OIL SYSTEM
Who is responsible for ensuring that PMS is performed on eyewash stations?
DIVISION OFFICER
Which of the following tags/labels prohibits operation of equipment that could
endanger personnel or equipment?
DANGER TAG
Maintenance aboard ship is the responsibility of the .......
SHIPS FORCE
ANSWERS 2024 GRADED A+
What ARE 3 considerations when dealing with electrical burns?
Electrical current may burn a large area just below the surface
Perform CPR if needed
Treatment is the same as for a thermal burn
(True/False) Section 300 of the PQS book list infrequent task and abnormal
conditions.
TRUE
The overall purpose of PQS is to ......
provide a means to qualify ships personnel.
(True/False) PQS provides an effective way to monitor an individual's
qualification progress.
TRUE
When can your Final Qualification Page be signed?.
After all line items have been completed and signed
Vocabulary used in each qualification can be found in the ....... Section of the
PQS book.
FUNDAMENTALS
Progress and completed qualifications of each person in the division are
displayed on/in the .......
PROGRESS CHART
Who is the final qualification authority?
COMMANDING OFFICER
A five inch outside micrometer will measure objects that are ....... inches thick.
4-5IN
A Dial indicator may be used to.......
ALIGN MACHINERY
It is NOT safe to operate electrical power tools in areas where ....... is/are
present.
FLAMMABLE GASES
Electrical power tools must be inspected prior to issue by a qualified .......
ELECTRICIAN
A torque wrench is used to measure the tightness of ...
FASTENERS
Torque wrenches are considered ....... equipment
PRECISION
If a maintenance procedure does not specify a torque sequence, utilize the
recommended sequence found in .......
NTM CHAPER 075
Which document contains maintenance requirements pertaining to all
equipment in a command?
PMS MASTER FILE
16. Which portion of the PMS Master File provides the work center supervisor
a ready reference of planned maintenance requirements.?
WORK CENTER PMS MANUAL
, If a planned maintenance action cannot be completed in accordance with the
steps listed on the MRC, the maintenance man should .......
STOP AND REPORT TO THE WCS
What is used to notify personnel that death or injury may result if the operating
procedures and practices are NOT correctly followed?
Warnings
Which of the following serves as the "Table of Contents" for the Work Center
PMS manual?
LIST OF EFFECTIVE PAGES (LOEP)
The SYSCOM Control Number assigned for each maintenance requirement
listed in a MIP must match the number on the corresponding
MRC (maintenance requirement card)
Materials needed to perform the required maintenance are found on the
FRONT OF THE MRC
The responsibility to replace a missing MRC belongs to the .......
WORK CENTER SUPERVISOR
Who assists the Department Head in managing maintenance at the division
level?
DIVISION OFFICER
Who has the responsibility to maintain the list of effective pages?
WORK CENTER SUPERVISOR
Which schedule is NOT used in the 3M system?
DAILY
Which of the following periodicity code is used when a maintenance
requirement is performed monthly?
M
Which document is use to verify that you have the proper MRC?
MIP (MAINTENANCE INDEX PAGE)
You must check the ...... to ensure that the weekly schedule is correct.
QUARTELY SCHEDULE
Material needed to perform a specific PMS action is listed on the ......
MRC (MAINTENANCE REQUIREMENT CARD)
The maintenance procedure steps on the MRC are
TO BE FOLLOWED PRECISELY
The shipboard hazardous material list is provided ...... on the Department of
Defense's CDROM.
QUARTERLY
Requirements for storage of hazardous material are found on the ......
MSDS
While grinding or chiseling, what should be used to protect the eyes?
CHIPPING GOGGLES
Which procedure does NOT require eye protection?
NORMAL OPERATION OF A LUBE OIL SYSTEM
Who is responsible for ensuring that PMS is performed on eyewash stations?
DIVISION OFFICER
Which of the following tags/labels prohibits operation of equipment that could
endanger personnel or equipment?
DANGER TAG
Maintenance aboard ship is the responsibility of the .......
SHIPS FORCE
