Woodshop Test Question With Correct
Answers.Already Passs!!!
4 inches
maintain a _____ margin of safety from the blade, This means that you must keep your hands _______
away from the saw blade.
safety glasses
wear ______
proper
keep the blade guard in the ______ position at all times
firmly, fence
hold stock ____ on the table and against the ____ so it does not shift or kick out when using the miter
saw
complete stop
after making a cut, but before raising the saw blade on the miter saw make sure that the blade has come
to a ____
under
never move your hands _____ the blade, whether it is moving or not on the miter saw
7 inches
all wood scrap goes in the fire pit bin, not the scrap bin unless it's over _____ long
cross
the miter saw will only be used for a type of cut called ______
cutting to fast, board is moving, board not completely pushed back on fence, board is warped
4 main safety concerns for kickback or binding on the miter saw
miter saw
step one in squaring a board
miter saw
used for crosscutting wood to rough or exact length (1/8th inches long)
jointer
second step in squaring a board
, Jointer
used for jointing and edging wood
best
joint the _____ edge on your board
adjust
do not remove the quard. do not _____ the jointer without shop teachers permission
1/16th inch
maximum cut depth for jointing an edge is _____
7 inches, 3/8th inch
stock must be at least _____ long to pass through and at least _____ inches thick on the jointer
with
feed the work so that the knives will cut "_____ the grain" on the jointer (only use new stock that is free
of knots , splits and checks)
guard
keep your hands away from the cutter head, even though the ______ is in position on the jointer
4 inches
maintain at least a ____ margin of safety. this means that your hands should always be at least _____
from the cutter head at all times
knives
use a push stick when jointing a flat surface or a board that is less than 4 inches high. never apply
pressure direction over the _____ with your hand
end
do not joint _____ grains on the jointer
sharp
jointer knives must be _____. dull knives will vibrate the stock and may cause a kickback
3/8
material cannot be less than ______ thick on the jointer
machine, work area
you must clean the ______ and ______ when done with jointer
table saw
Answers.Already Passs!!!
4 inches
maintain a _____ margin of safety from the blade, This means that you must keep your hands _______
away from the saw blade.
safety glasses
wear ______
proper
keep the blade guard in the ______ position at all times
firmly, fence
hold stock ____ on the table and against the ____ so it does not shift or kick out when using the miter
saw
complete stop
after making a cut, but before raising the saw blade on the miter saw make sure that the blade has come
to a ____
under
never move your hands _____ the blade, whether it is moving or not on the miter saw
7 inches
all wood scrap goes in the fire pit bin, not the scrap bin unless it's over _____ long
cross
the miter saw will only be used for a type of cut called ______
cutting to fast, board is moving, board not completely pushed back on fence, board is warped
4 main safety concerns for kickback or binding on the miter saw
miter saw
step one in squaring a board
miter saw
used for crosscutting wood to rough or exact length (1/8th inches long)
jointer
second step in squaring a board
, Jointer
used for jointing and edging wood
best
joint the _____ edge on your board
adjust
do not remove the quard. do not _____ the jointer without shop teachers permission
1/16th inch
maximum cut depth for jointing an edge is _____
7 inches, 3/8th inch
stock must be at least _____ long to pass through and at least _____ inches thick on the jointer
with
feed the work so that the knives will cut "_____ the grain" on the jointer (only use new stock that is free
of knots , splits and checks)
guard
keep your hands away from the cutter head, even though the ______ is in position on the jointer
4 inches
maintain at least a ____ margin of safety. this means that your hands should always be at least _____
from the cutter head at all times
knives
use a push stick when jointing a flat surface or a board that is less than 4 inches high. never apply
pressure direction over the _____ with your hand
end
do not joint _____ grains on the jointer
sharp
jointer knives must be _____. dull knives will vibrate the stock and may cause a kickback
3/8
material cannot be less than ______ thick on the jointer
machine, work area
you must clean the ______ and ______ when done with jointer
table saw
