SHP Final Exam Questions With 100% Correct
Answers
True
The firefighter may be installed next to a stand-alone battery smoke detector
False
When performing a full system test, you may bypass any open doors or windows
Always enable the emergency
When programming an skey1,you must
False
When running power to the take345,polarity doesn't apply
Audible alarm (7)
When programming the emergency key for the skey1,which zone/sensor type is used.
True
When installing a smkt3,you must use the included screws and anchors
True
When installing the firefighter, it is required to test the customers existing smoke detectors
Between 6"(15cm) and 2'(61cm) from floor
When installing a Dw21, where is the approved location for the sensor
Provided double sided tape
When installing a dw11 on a vinyl or metal frame, what should primarily use to mount the sensor
Beans & wire caps
Which of the following materials can you use to group multiple ground terminals in a takeover.
Smoke detector
Which of the following sensors are you not allowed to program using a translator
True
When installing the take345, you must always test the new 12v battery before using it.
16.5
What is the output voltage of transformer used to power the sky control
12"
What is the minimum distance for placement of a co3 from the corners of the wall
, False
The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14
How would you program a co3 if mounted on a hallway wall
False
When installing a translator, you must program all of the existing sensors as new equipment on the
panel
True
The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze
Which of the following zone/sensor types are correct when programming an smkt3
7ft
What it the correct height ar which to install the Pir2
Loop 2
When programming a Dw21 what loop number is used
True
When programming a sensor into a sky control panel, you can type in the serial number or learn it in
by triggering the device.
Loop 1 Zone 3
How would you program a gb2 when it is mounted on a master bedroom ceiling
True
Panic pendants are programmed as an audible alarm(type 07)
True
When installing the take 345 you must ensure that the transformer is supplying power to the power
supply before connecting the battery
True
When wiring the take 345 you must ensure it has three points of ground: the low side of each zone,
the takeover module, and the power supply
True
You are required to test all secondary keypads and key fobs even though they are not detection
devices
Answers
True
The firefighter may be installed next to a stand-alone battery smoke detector
False
When performing a full system test, you may bypass any open doors or windows
Always enable the emergency
When programming an skey1,you must
False
When running power to the take345,polarity doesn't apply
Audible alarm (7)
When programming the emergency key for the skey1,which zone/sensor type is used.
True
When installing a smkt3,you must use the included screws and anchors
True
When installing the firefighter, it is required to test the customers existing smoke detectors
Between 6"(15cm) and 2'(61cm) from floor
When installing a Dw21, where is the approved location for the sensor
Provided double sided tape
When installing a dw11 on a vinyl or metal frame, what should primarily use to mount the sensor
Beans & wire caps
Which of the following materials can you use to group multiple ground terminals in a takeover.
Smoke detector
Which of the following sensors are you not allowed to program using a translator
True
When installing the take345, you must always test the new 12v battery before using it.
16.5
What is the output voltage of transformer used to power the sky control
12"
What is the minimum distance for placement of a co3 from the corners of the wall
, False
The smkt3 has 2 function:smoke and heat detection
Loop 1 Zone 14
How would you program a co3 if mounted on a hallway wall
False
When installing a translator, you must program all of the existing sensors as new equipment on the
panel
True
The dw21 should always be installed in the door frame
(09) Smoke detector. (09) Heat detector. (08) Freeze
Which of the following zone/sensor types are correct when programming an smkt3
7ft
What it the correct height ar which to install the Pir2
Loop 2
When programming a Dw21 what loop number is used
True
When programming a sensor into a sky control panel, you can type in the serial number or learn it in
by triggering the device.
Loop 1 Zone 3
How would you program a gb2 when it is mounted on a master bedroom ceiling
True
Panic pendants are programmed as an audible alarm(type 07)
True
When installing the take 345 you must ensure that the transformer is supplying power to the power
supply before connecting the battery
True
When wiring the take 345 you must ensure it has three points of ground: the low side of each zone,
the takeover module, and the power supply
True
You are required to test all secondary keypads and key fobs even though they are not detection
devices
