Hand tools and power tools Exam Questions
And Answers Updated 2024/2025
What hand saw would you choose to cut a piece of wood with the grain?
Ripsaw
What tool would you use to pull electrical wires through a conduit?
Fish tape
What material would you choose for a level?
aluminum
What task would you not use for electrical pliers?
hammering
True or False: A tang chisel is made for heavy duty chiseling?
False
What tool would you select to install a screw in a hard to reach place?
off-set screw driver
The cut made by a saw blade is called the
kerf
What tool is used to remove the insulation from small wires?
The all-purpose tool
What is the most common tool to pull fuses?
Fuse puller
To correctly use a measuring tape you should always
Hold the tape straight with no sag, Make sure there are not tears in the tape, Make sure you have the
hook on the correct item you're measuring (ALL OF THE ABOVE)
The common sizes of a _____________ are 1/4, 3/8, and 1/2 in.
Drive lug
Measuring tools are used to make what type of measurements?
Linear, Angular (Both A & C)
To find the correct socket or wrench for a nut or bolt, you will need to measure?
The distance across the flats
True or False: Typically on a measuring tape, the inch is divided as low as sixty-fourths of an inch.
, False
Most squares have a _________ along one or more of the edges.
scale
What type of caliper would you use to measure the inside of a hole?
inside
What type of material are the handles of a screw drive made out of?
Wood, hard rubber, and plastic (ALL OF THE ABOVE)
True or False: The handles of a screw driver are usually made of a material that insulate against
electrical shock
True
For heavy duty turning on a nut or bolt with a box-end wrench, you would select a
6-point wrench
What is the most common head on a combination square?
Square head
A torque wrench is used to
Measure the twisting force applied
The short arm on a framing square is called the
tongue
What is the stationary jaw on a pipe wrench called?
the heel
What wrench would you use to tighten or loosen a finished product such as polished metal?
strap wrench
What tool would you use to unclog a server blockage in a toilet?
closet auger
To turn a nut in a narrow space between a sink and a wall, you would use a
Basin wrench
A ________ cuts thread on the outside of a pipe
Threading pipe
When cutting heavy grade cast-iron pipe, what tools would you select?
And Answers Updated 2024/2025
What hand saw would you choose to cut a piece of wood with the grain?
Ripsaw
What tool would you use to pull electrical wires through a conduit?
Fish tape
What material would you choose for a level?
aluminum
What task would you not use for electrical pliers?
hammering
True or False: A tang chisel is made for heavy duty chiseling?
False
What tool would you select to install a screw in a hard to reach place?
off-set screw driver
The cut made by a saw blade is called the
kerf
What tool is used to remove the insulation from small wires?
The all-purpose tool
What is the most common tool to pull fuses?
Fuse puller
To correctly use a measuring tape you should always
Hold the tape straight with no sag, Make sure there are not tears in the tape, Make sure you have the
hook on the correct item you're measuring (ALL OF THE ABOVE)
The common sizes of a _____________ are 1/4, 3/8, and 1/2 in.
Drive lug
Measuring tools are used to make what type of measurements?
Linear, Angular (Both A & C)
To find the correct socket or wrench for a nut or bolt, you will need to measure?
The distance across the flats
True or False: Typically on a measuring tape, the inch is divided as low as sixty-fourths of an inch.
, False
Most squares have a _________ along one or more of the edges.
scale
What type of caliper would you use to measure the inside of a hole?
inside
What type of material are the handles of a screw drive made out of?
Wood, hard rubber, and plastic (ALL OF THE ABOVE)
True or False: The handles of a screw driver are usually made of a material that insulate against
electrical shock
True
For heavy duty turning on a nut or bolt with a box-end wrench, you would select a
6-point wrench
What is the most common head on a combination square?
Square head
A torque wrench is used to
Measure the twisting force applied
The short arm on a framing square is called the
tongue
What is the stationary jaw on a pipe wrench called?
the heel
What wrench would you use to tighten or loosen a finished product such as polished metal?
strap wrench
What tool would you use to unclog a server blockage in a toilet?
closet auger
To turn a nut in a narrow space between a sink and a wall, you would use a
Basin wrench
A ________ cuts thread on the outside of a pipe
Threading pipe
When cutting heavy grade cast-iron pipe, what tools would you select?
