Woodshop Safety Test Exam Questions With
Answers
If the instructor is out of the room, all power tools and machines must be ________
off
Adjustments on all power tools and machines must be made before turning on the _________
machine, power
In case you receive an injury, report it to your ____________
teacher
Eye protection is required when operating or observing in close proximity all power activated
____________
machines
When working at the shop tables, all work must be clamped to the table or held secure in the
__________
vise
The shortest length of stock to be run through the planer with safety is _____
12"
Scraps of lumber must be cleared away from a power machine with a _______
push stick
All "special" machine setups (resawing, plowing, grooving, dadoing, and tapering) must be checked by
the instructor before turning on the _________
power panel
To avoid possible injury, students with long hair must wear a headband, hair net, snoot. or similar
device to prevent hair from becoming entangled in ___________
moving parts
When sanding stock on the disk sander, use only that part of the disk that is traveling _________
down
Chisels must be hit with a mallet with the chisel facing away from your ____________
body
When crosscutting or ripping stock, you must cover the circular saw blade with a __________
guard
The circular saw blade should be raised above the stock to be cut not more than _________
1/4
, When working with tools and machines you must protect your feet and toes by wearing _________
shoes
Tools with sharp points or ends should be carried with the sharp end pointing towards the _________
floor
Before leaving the shaper or any other machine for any reason, shut off the power and wait until the
machine has _________
stopped
The purpose of the splitter on the circular saw is to prevent the wood from _________
binding
Before the operator of a router changes a bit, a cutter, or makes any adjustments, he or she must
disconnect the _________
plug
When turning or sanding on the lathe, the operator must always wear a ________
face shield
When ripping narrow pieces of stock on the circular saw, you must always use a _____ or a _____ to
keep fingers a safe distance away from the blade (two answers)
push stick or push block
When crosscutting short pieces of stock on the circular saw, you must fasten a clearance block to the
_____ to prevent binding and kick-backs _________
fence
When face planning on the jointer, allow a minimum stock thickness of _________
1/2
The shortest length of stock to be run through the Jointer with safety is _________
12"
When face planning narrow pieces of stock on the jointer, you must always use a ________
push block
The clearance between the band-saw guide and the stock to be cut should not be more than _______
1/4
When work is placed between centers on the wood-turning lathe, the tail stock must be securely
_______
fastened
Answers
If the instructor is out of the room, all power tools and machines must be ________
off
Adjustments on all power tools and machines must be made before turning on the _________
machine, power
In case you receive an injury, report it to your ____________
teacher
Eye protection is required when operating or observing in close proximity all power activated
____________
machines
When working at the shop tables, all work must be clamped to the table or held secure in the
__________
vise
The shortest length of stock to be run through the planer with safety is _____
12"
Scraps of lumber must be cleared away from a power machine with a _______
push stick
All "special" machine setups (resawing, plowing, grooving, dadoing, and tapering) must be checked by
the instructor before turning on the _________
power panel
To avoid possible injury, students with long hair must wear a headband, hair net, snoot. or similar
device to prevent hair from becoming entangled in ___________
moving parts
When sanding stock on the disk sander, use only that part of the disk that is traveling _________
down
Chisels must be hit with a mallet with the chisel facing away from your ____________
body
When crosscutting or ripping stock, you must cover the circular saw blade with a __________
guard
The circular saw blade should be raised above the stock to be cut not more than _________
1/4
, When working with tools and machines you must protect your feet and toes by wearing _________
shoes
Tools with sharp points or ends should be carried with the sharp end pointing towards the _________
floor
Before leaving the shaper or any other machine for any reason, shut off the power and wait until the
machine has _________
stopped
The purpose of the splitter on the circular saw is to prevent the wood from _________
binding
Before the operator of a router changes a bit, a cutter, or makes any adjustments, he or she must
disconnect the _________
plug
When turning or sanding on the lathe, the operator must always wear a ________
face shield
When ripping narrow pieces of stock on the circular saw, you must always use a _____ or a _____ to
keep fingers a safe distance away from the blade (two answers)
push stick or push block
When crosscutting short pieces of stock on the circular saw, you must fasten a clearance block to the
_____ to prevent binding and kick-backs _________
fence
When face planning on the jointer, allow a minimum stock thickness of _________
1/2
The shortest length of stock to be run through the Jointer with safety is _________
12"
When face planning narrow pieces of stock on the jointer, you must always use a ________
push block
The clearance between the band-saw guide and the stock to be cut should not be more than _______
1/4
When work is placed between centers on the wood-turning lathe, the tail stock must be securely
_______
fastened
