API 1169. Study test questions test RM#2
According to OSHA a "protective system" is defined as:
Method of protecting employees from cave-ins.
Design and development inputs shall be identified and reviewed for?
Accuracy, completeness and lack of conflict
The Excavator calls the One Call Center prior to excavation at least
Two working days nor more than ten working days
Encroachment Area is the area where the ground disturbance occurs within:
50 feet of the centerline of the existing facility (or ROW) or other easement
The pressure recorders and deadweight gauge shall be located at a safe distance at least:
100 feet from the facility being tested
In compliance with the Uniform Color Code the route and or area to be excavated shall be identified
by:
White markers
Markings may include one or any combination of the following: paint, chalk, flags, stakes, brushes, or
offsets. Matching markings to existing and expected surface conditions is the responsibility of?
Facility Owner
Subpart G of 49CFR192 prescribes minimum requirements for:
Construction of transmission pipelines and mains.
If a newspaper was seeking information about the project, are inspection personnel allowed to
interac with them to answer their questions?
Only if expressly allowed
Before placing new gas pipelines in service all piping and components must be subjected to:
125% of MOP (maximum operational pressure) of the system for 4 hours
A detailed design developed from operating requirements and conforming to Code requirements
including all necessary drawings and specifications, goveming a liquid petroleum pipeline installation
is also known as?
Engineering design
Planned, systematic, and preventative actions that are required to ensure that materials, products
and services will meet specified requirements is called?
Quality Control system
, Any physical objects detected by an in-line inspection device that may be anomalies, components,
nearby metallic objects, or some other item are also known as?
Features
Which describes "rework" the best?
Any grinding or welding on a completed weld to correct potentially rejectable indications
General basic requirements for Chief Inspector qualification are?
Environmental and pollution control
What type of hazard is a waterway crossing?
Site-Specific
What would a continuous run of pipe between adjacent blocks valves be called?
A pipeline section
Does a section of pipe removed and scheduled for reuse, but then reinstalled in the same loca need to
be retested?
No testing required
In intemational codes and standards, this is often referred to as the maximum steady state op
pressure or maximum allowable operating pressure
Operating pressure limit
The letter "I" identifies shipping names appropriate for:
.Describing materials in intermational transportation
Who is responsible for all safety on the job site?
Contractor
What identifies hazards that necessitate the use of PPE?
JSA
Which is an example of a sustained load?
The weight of the pipeline including components, fluids, and slurries
What is the standard of acceptance for welds of piping systems operating at hoop stress levels 50% of
the SMYS?
ASME B31,8
In regards to road and highway use, what should the Inspector be aware of?
Size and weight restrictions for heavy equipment
It is not necessary to vary the design stress for metal temperatures between what range?
According to OSHA a "protective system" is defined as:
Method of protecting employees from cave-ins.
Design and development inputs shall be identified and reviewed for?
Accuracy, completeness and lack of conflict
The Excavator calls the One Call Center prior to excavation at least
Two working days nor more than ten working days
Encroachment Area is the area where the ground disturbance occurs within:
50 feet of the centerline of the existing facility (or ROW) or other easement
The pressure recorders and deadweight gauge shall be located at a safe distance at least:
100 feet from the facility being tested
In compliance with the Uniform Color Code the route and or area to be excavated shall be identified
by:
White markers
Markings may include one or any combination of the following: paint, chalk, flags, stakes, brushes, or
offsets. Matching markings to existing and expected surface conditions is the responsibility of?
Facility Owner
Subpart G of 49CFR192 prescribes minimum requirements for:
Construction of transmission pipelines and mains.
If a newspaper was seeking information about the project, are inspection personnel allowed to
interac with them to answer their questions?
Only if expressly allowed
Before placing new gas pipelines in service all piping and components must be subjected to:
125% of MOP (maximum operational pressure) of the system for 4 hours
A detailed design developed from operating requirements and conforming to Code requirements
including all necessary drawings and specifications, goveming a liquid petroleum pipeline installation
is also known as?
Engineering design
Planned, systematic, and preventative actions that are required to ensure that materials, products
and services will meet specified requirements is called?
Quality Control system
, Any physical objects detected by an in-line inspection device that may be anomalies, components,
nearby metallic objects, or some other item are also known as?
Features
Which describes "rework" the best?
Any grinding or welding on a completed weld to correct potentially rejectable indications
General basic requirements for Chief Inspector qualification are?
Environmental and pollution control
What type of hazard is a waterway crossing?
Site-Specific
What would a continuous run of pipe between adjacent blocks valves be called?
A pipeline section
Does a section of pipe removed and scheduled for reuse, but then reinstalled in the same loca need to
be retested?
No testing required
In intemational codes and standards, this is often referred to as the maximum steady state op
pressure or maximum allowable operating pressure
Operating pressure limit
The letter "I" identifies shipping names appropriate for:
.Describing materials in intermational transportation
Who is responsible for all safety on the job site?
Contractor
What identifies hazards that necessitate the use of PPE?
JSA
Which is an example of a sustained load?
The weight of the pipeline including components, fluids, and slurries
What is the standard of acceptance for welds of piping systems operating at hoop stress levels 50% of
the SMYS?
ASME B31,8
In regards to road and highway use, what should the Inspector be aware of?
Size and weight restrictions for heavy equipment
It is not necessary to vary the design stress for metal temperatures between what range?
