Steering and suspension test
A customer complains that the steering lacks power assist all the time. Tech a says that the
power steering pump drive belt could be slipping or loose. Tech b says that worn outer tie
rod ends could be the cause. Who is correct? - correct answer-Tech A
A front wheel drive vehicle pulls towards the right during hard acceleration. The most likely
cause is? - correct answer-Normal torque steer
When replacing a rubber-bonded socket the rod end, the tech should be sure to? - correct
answer-Install and tighten the replacement with the front wheels in the straight ahead
position
Whenever installing a tire on a rim, do not exceed - correct answer-40psi
Two technicians are discussing mounting a tire on a wheel. Tech a says that for best
balance, the tire should be match mounted. Tech b says that silicone spray should be used
to lubricants the tire bend. Which is correct? - correct answer-Tech A
Technician A says that radial tires should only be rotated front to rear, never side to side.
Tech b says that vehicle manufacturers usually recommend radial tires should be rotated
using the modified x method. Which is correct? - correct answer-Tech b
For a tire that has excessive radial runout, tech a says that it should be broken down on a
tire changing machine and then rotated 180 degrees on the wheel and retested. Tech b says
that the tire should be replaced. Which tech is correct? - correct answer-Tech a
Technician a says that overloading a vehicle can cause damage to the wheel bearings. Tech
b says that tappered roller bearings used on a non drive wheel should be adjusted hand tight
only after seating. Which tech is correct? - correct answer-Both
Defective wheel bearings usually sound like a? - correct answer-Growl, rumble, snow tires
A defective outer CV joint will usually make a clicking noise when? - correct answer-While
turning and moving
The proper lubricant usually specified for use in a differential is? - correct answer-SAE
80w-90 GL5
A vehicle owner complained that a severe vibration was felt throughout the entire vehicle
only during rapid acceleration from stop and up to about 20 mph. The most likely cause is? -
correct answer-In equal drive shaft working angles
To remove a c-clip axle what step does not need to be done? - correct answer-Remove the
axle flange bolts/nuts
A customer complains that the steering lacks power assist all the time. Tech a says that the
power steering pump drive belt could be slipping or loose. Tech b says that worn outer tie
rod ends could be the cause. Who is correct? - correct answer-Tech A
A front wheel drive vehicle pulls towards the right during hard acceleration. The most likely
cause is? - correct answer-Normal torque steer
When replacing a rubber-bonded socket the rod end, the tech should be sure to? - correct
answer-Install and tighten the replacement with the front wheels in the straight ahead
position
Whenever installing a tire on a rim, do not exceed - correct answer-40psi
Two technicians are discussing mounting a tire on a wheel. Tech a says that for best
balance, the tire should be match mounted. Tech b says that silicone spray should be used
to lubricants the tire bend. Which is correct? - correct answer-Tech A
Technician A says that radial tires should only be rotated front to rear, never side to side.
Tech b says that vehicle manufacturers usually recommend radial tires should be rotated
using the modified x method. Which is correct? - correct answer-Tech b
For a tire that has excessive radial runout, tech a says that it should be broken down on a
tire changing machine and then rotated 180 degrees on the wheel and retested. Tech b says
that the tire should be replaced. Which tech is correct? - correct answer-Tech a
Technician a says that overloading a vehicle can cause damage to the wheel bearings. Tech
b says that tappered roller bearings used on a non drive wheel should be adjusted hand tight
only after seating. Which tech is correct? - correct answer-Both
Defective wheel bearings usually sound like a? - correct answer-Growl, rumble, snow tires
A defective outer CV joint will usually make a clicking noise when? - correct answer-While
turning and moving
The proper lubricant usually specified for use in a differential is? - correct answer-SAE
80w-90 GL5
A vehicle owner complained that a severe vibration was felt throughout the entire vehicle
only during rapid acceleration from stop and up to about 20 mph. The most likely cause is? -
correct answer-In equal drive shaft working angles
To remove a c-clip axle what step does not need to be done? - correct answer-Remove the
axle flange bolts/nuts
