NASCLA Exam Practice Questions Pt. 1
Which type of device is most accurate to determine a reference plane for leveling? -
ANS-Theodolite
Each suspension rope used on non-adjustable suspension scaffolds shall be capable of
supporting at least ___ the maximum intended load applied to that rope. - ANS-6 times
What can have detrimental impacts on the environment? - ANS-Stormwater runoff
When is the deadline to file electronic W-2 Forms with the Social Security
Administration? - ANS-3/31/2021 12:00:00 AM
Stair headroom is measured from the ceiling directly above which point? - ANS-Edge of
nosing
When reviewing plans and detail drawings, size means inches to ____, and scale
means inches to ____. - ANS-Inches, feet
When mobile scaffolds are being used in a stationary manner, what preventative
measures shall be used to prevent movement of the scaffold? - ANS-Positive wheel
and/or wheel and swivel locks
What is the primary purpose of erosion and sediment controls? - ANS-To protect
surface waters
Which mortar type is useful for structures below grade, manholes, and catch basins? -
ANS-Type M
Which of the following forms of business ownership is least regulated? - ANS-Sole
proprietor
What is the minimum gauge for a metal deck that will have side laps welded? - ANS-20
gauge or heavier
Which type of projects are track loaders best suited for? - ANS-Projects where good
traction and reduced ground pressures are required.
, What is the maximum width of a swinging door leaf? - ANS-48 inches
The _______ will show how a steel joist girder is recommended to be placed. - ANS-Tag
end
What is an invitation to bid? - ANS-A document that gives a brief overview of the
project, deadlines, and general requirements.
In a Type A unit, if measuring to the highest part of the rim or highest part of the counter,
what is the maximum height of the sink front above the floor? - ANS-34"
Which roof rafters extend diagonally from the corners formed by the top plates to the
ridge board? - ANS-Hip
A semi-U blade fitted to a mid-sized dozer increases capacity by about _____ % over
that of a straight blade. - ANS-40%
The equation that is used for determining the Height or grade is: - ANS-HI = BM + BS
Which of the following is NOT a recommendation for effective heating & cooling? -
ANS-Use of HCFC's as a refrigerant
Oxygen cylinders, regulators, hoses, and fittings shall be kept away from ______ by at
least 20 feet. - ANS-Oil and grease
What would be the best method to use for off-loading the post-tensioning cable from a
flatbed truck? - ANS-Nylon strap that cradles the coil by passing through the center of
the bundle
How much money is deducted from an employee's pay for workers' compensation
insurance? - ANS-0
Where is window flashing required? - ANS-Head only
A building with aggregate roofing in an area with a nominal design wind speed of 110
mph in exposure category C can have a maximum roof height of how many feet? -
ANS-NP - Not Permitted
Which type of device is most accurate to determine a reference plane for leveling? -
ANS-Theodolite
Each suspension rope used on non-adjustable suspension scaffolds shall be capable of
supporting at least ___ the maximum intended load applied to that rope. - ANS-6 times
What can have detrimental impacts on the environment? - ANS-Stormwater runoff
When is the deadline to file electronic W-2 Forms with the Social Security
Administration? - ANS-3/31/2021 12:00:00 AM
Stair headroom is measured from the ceiling directly above which point? - ANS-Edge of
nosing
When reviewing plans and detail drawings, size means inches to ____, and scale
means inches to ____. - ANS-Inches, feet
When mobile scaffolds are being used in a stationary manner, what preventative
measures shall be used to prevent movement of the scaffold? - ANS-Positive wheel
and/or wheel and swivel locks
What is the primary purpose of erosion and sediment controls? - ANS-To protect
surface waters
Which mortar type is useful for structures below grade, manholes, and catch basins? -
ANS-Type M
Which of the following forms of business ownership is least regulated? - ANS-Sole
proprietor
What is the minimum gauge for a metal deck that will have side laps welded? - ANS-20
gauge or heavier
Which type of projects are track loaders best suited for? - ANS-Projects where good
traction and reduced ground pressures are required.
, What is the maximum width of a swinging door leaf? - ANS-48 inches
The _______ will show how a steel joist girder is recommended to be placed. - ANS-Tag
end
What is an invitation to bid? - ANS-A document that gives a brief overview of the
project, deadlines, and general requirements.
In a Type A unit, if measuring to the highest part of the rim or highest part of the counter,
what is the maximum height of the sink front above the floor? - ANS-34"
Which roof rafters extend diagonally from the corners formed by the top plates to the
ridge board? - ANS-Hip
A semi-U blade fitted to a mid-sized dozer increases capacity by about _____ % over
that of a straight blade. - ANS-40%
The equation that is used for determining the Height or grade is: - ANS-HI = BM + BS
Which of the following is NOT a recommendation for effective heating & cooling? -
ANS-Use of HCFC's as a refrigerant
Oxygen cylinders, regulators, hoses, and fittings shall be kept away from ______ by at
least 20 feet. - ANS-Oil and grease
What would be the best method to use for off-loading the post-tensioning cable from a
flatbed truck? - ANS-Nylon strap that cradles the coil by passing through the center of
the bundle
How much money is deducted from an employee's pay for workers' compensation
insurance? - ANS-0
Where is window flashing required? - ANS-Head only
A building with aggregate roofing in an area with a nominal design wind speed of 110
mph in exposure category C can have a maximum roof height of how many feet? -
ANS-NP - Not Permitted
