Safety instructions must be given before allowed to work/operate on any machine or
- CORRECT ANSWER-Tool
You're not permitted to work on any equipment/machine if the instructor is not -
CORRECT ANSWER-Present
Guards and safety devices must be on all machines during - CORRECT
ANSWER-Operation
Machinery must not be oiled or adjusted while in - CORRECT ANSWER-Use
A machine must be started and stopped only by the - CORRECT ANSWER-Operator
Do not leave a machine while it is - CORRECT ANSWER-Running
When working on or near any machine or tool where there's a possibility of eye
injury, you must wear - CORRECT ANSWER-Eye protection
You are not permitted within the safety zone around any machine unless you are the
- CORRECT ANSWER-Operator
Loose clothing must be tucked in before you start work, as a precaution against -
CORRECT ANSWER-Getting tangled
If in doubt about any machine, check with the - CORRECT ANSWER-Instructor
Aisled and working areas must be kept clear of - CORRECT ANSWER-All
obstructions
The shop floor must be kept free of oil because of danger of fire and - CORRECT
ANSWER-Slipping
Combustible rags must be kept in a closed - CORRECT ANSWER-Red container
Do not lift materials heavier than your ability to handle them - CORRECT
ANSWER-Safely
Long pieces of material should be carried by - CORRECT ANSWER-2 people
, The attention of the instructor should be directed to any violation of - CORRECT
ANSWER-The Rules
Accidents, no matter how slight, must be reported immediately to the - CORRECT
ANSWER-Instructor
Carry sharp-pointed tools pointed - CORRECT ANSWER-Downward
Do not leave tools and materials ____ from a vise or bench - CORRECT
ANSWER-clamped
A dull tool is dangerous because it will - CORRECT ANSWER-Skip
Pass tools to classmates with the tool handles - CORRECT ANSWER-Toward them
Do not stand in front of anyone using a sharp - CORRECT ANSWER-Tool
Carry a hand saw by the handle with the toe - CORRECT ANSWER-Pointed
downward
When using a screwdriver, avoid holding the material in the - CORRECT
ANSWER-Hand
After clamps have been applied to the work, it should not be - CORRECT
ANSWER-Moved
Face shields or goggles/glasses must be worn by shop students when there's a
possibilty of - CORRECT ANSWER-Loose Debris
Whenever possible, the ____ should be clamped - CORRECT ANSWER-Project
stock
All adjustments should be made before the machine is - CORRECT
ANSWER-Turned on
The operator must keep his/her fingers away from the ____ spindle, chuck, and bit -
CORRECT ANSWER-Spinning
- CORRECT ANSWER-Tool
You're not permitted to work on any equipment/machine if the instructor is not -
CORRECT ANSWER-Present
Guards and safety devices must be on all machines during - CORRECT
ANSWER-Operation
Machinery must not be oiled or adjusted while in - CORRECT ANSWER-Use
A machine must be started and stopped only by the - CORRECT ANSWER-Operator
Do not leave a machine while it is - CORRECT ANSWER-Running
When working on or near any machine or tool where there's a possibility of eye
injury, you must wear - CORRECT ANSWER-Eye protection
You are not permitted within the safety zone around any machine unless you are the
- CORRECT ANSWER-Operator
Loose clothing must be tucked in before you start work, as a precaution against -
CORRECT ANSWER-Getting tangled
If in doubt about any machine, check with the - CORRECT ANSWER-Instructor
Aisled and working areas must be kept clear of - CORRECT ANSWER-All
obstructions
The shop floor must be kept free of oil because of danger of fire and - CORRECT
ANSWER-Slipping
Combustible rags must be kept in a closed - CORRECT ANSWER-Red container
Do not lift materials heavier than your ability to handle them - CORRECT
ANSWER-Safely
Long pieces of material should be carried by - CORRECT ANSWER-2 people
, The attention of the instructor should be directed to any violation of - CORRECT
ANSWER-The Rules
Accidents, no matter how slight, must be reported immediately to the - CORRECT
ANSWER-Instructor
Carry sharp-pointed tools pointed - CORRECT ANSWER-Downward
Do not leave tools and materials ____ from a vise or bench - CORRECT
ANSWER-clamped
A dull tool is dangerous because it will - CORRECT ANSWER-Skip
Pass tools to classmates with the tool handles - CORRECT ANSWER-Toward them
Do not stand in front of anyone using a sharp - CORRECT ANSWER-Tool
Carry a hand saw by the handle with the toe - CORRECT ANSWER-Pointed
downward
When using a screwdriver, avoid holding the material in the - CORRECT
ANSWER-Hand
After clamps have been applied to the work, it should not be - CORRECT
ANSWER-Moved
Face shields or goggles/glasses must be worn by shop students when there's a
possibilty of - CORRECT ANSWER-Loose Debris
Whenever possible, the ____ should be clamped - CORRECT ANSWER-Project
stock
All adjustments should be made before the machine is - CORRECT
ANSWER-Turned on
The operator must keep his/her fingers away from the ____ spindle, chuck, and bit -
CORRECT ANSWER-Spinning
