Safety instructions must be given before you are allowed to work on or operate any
machine or - CORRECT ANSWER-tool
You are not permitted to work on any equipment or machine if the
____________________ is not present - CORRECT ANSWER-instructor
Guards and safety devices must be on all machines during - CORRECT
ANSWER-operation
Machinery must not be oiled or adjusted while in - CORRECT ANSWER-use
A machine must be started and stopped only by the - CORRECT ANSWER-operator
Do not leave a machine while it is - CORRECT ANSWER-running
When working on or near an machine or tool where there is a possibility of eye injury,
you must wear - CORRECT ANSWER-eye protection
You are not permitted within the safety zone around any machine unless you are the
- CORRECT ANSWER-operator
loose clothing must be tucked in before you start work, as a precaution against -
CORRECT ANSWER-getting entangled
If in doubt about any machine, check with the - CORRECT ANSWER-instructor
Aisles and working areas must be kept clear of - CORRECT ANSWER-all
obstructions
The shop floor must be kept free of oil because of the danger of fire and - CORRECT
ANSWER-slipping
Combustible rags must be kept in a closed - CORRECT ANSWER-red container
Do not lift materials heavier than your ability to handle them - CORRECT
ANSWER-safely
Long pieces of material should be carried by - CORRECT ANSWER-2 people
, The attention of the instructor should be directed to any violation of - CORRECT
ANSWER-rules
Accidents, no matter how slight, must be reported immediately to - CORRECT
ANSWER-the instructor
carry sharp-pointed tools pointed - CORRECT ANSWER-downward
do not leave tools and materials ____________ from a vise or a bench. - CORRECT
ANSWER-clamped
A dull tool is dangerous because it will - CORRECT ANSWER-skip
Pass tools to classmates with the tool handles - CORRECT ANSWER-toward them
Do not stand in front of anyone using a sharp - CORRECT ANSWER-tool
Carry a hand saw by the handle with the toe - CORRECT ANSWER-pointed
downward
When using a screwdriver, avoid holding the material in the - CORRECT
ANSWER-hand
After clamps have been applied to the work, it should not be - CORRECT
ANSWER-moved
Face shields or googles/glasses must be worn by shop students when there is a
possibility of - CORRECT ANSWER-loose debris
Whenever possible, the _________ should be clamped - CORRECT
ANSWER-project stock
All adjustments should be made before the machine is - CORRECT
ANSWER-turned on
The operator must keep his/her fingers away from the ________spindle, chuck, and
bit. - CORRECT ANSWER-spinning
machine or - CORRECT ANSWER-tool
You are not permitted to work on any equipment or machine if the
____________________ is not present - CORRECT ANSWER-instructor
Guards and safety devices must be on all machines during - CORRECT
ANSWER-operation
Machinery must not be oiled or adjusted while in - CORRECT ANSWER-use
A machine must be started and stopped only by the - CORRECT ANSWER-operator
Do not leave a machine while it is - CORRECT ANSWER-running
When working on or near an machine or tool where there is a possibility of eye injury,
you must wear - CORRECT ANSWER-eye protection
You are not permitted within the safety zone around any machine unless you are the
- CORRECT ANSWER-operator
loose clothing must be tucked in before you start work, as a precaution against -
CORRECT ANSWER-getting entangled
If in doubt about any machine, check with the - CORRECT ANSWER-instructor
Aisles and working areas must be kept clear of - CORRECT ANSWER-all
obstructions
The shop floor must be kept free of oil because of the danger of fire and - CORRECT
ANSWER-slipping
Combustible rags must be kept in a closed - CORRECT ANSWER-red container
Do not lift materials heavier than your ability to handle them - CORRECT
ANSWER-safely
Long pieces of material should be carried by - CORRECT ANSWER-2 people
, The attention of the instructor should be directed to any violation of - CORRECT
ANSWER-rules
Accidents, no matter how slight, must be reported immediately to - CORRECT
ANSWER-the instructor
carry sharp-pointed tools pointed - CORRECT ANSWER-downward
do not leave tools and materials ____________ from a vise or a bench. - CORRECT
ANSWER-clamped
A dull tool is dangerous because it will - CORRECT ANSWER-skip
Pass tools to classmates with the tool handles - CORRECT ANSWER-toward them
Do not stand in front of anyone using a sharp - CORRECT ANSWER-tool
Carry a hand saw by the handle with the toe - CORRECT ANSWER-pointed
downward
When using a screwdriver, avoid holding the material in the - CORRECT
ANSWER-hand
After clamps have been applied to the work, it should not be - CORRECT
ANSWER-moved
Face shields or googles/glasses must be worn by shop students when there is a
possibility of - CORRECT ANSWER-loose debris
Whenever possible, the _________ should be clamped - CORRECT
ANSWER-project stock
All adjustments should be made before the machine is - CORRECT
ANSWER-turned on
The operator must keep his/her fingers away from the ________spindle, chuck, and
bit. - CORRECT ANSWER-spinning
