4 inches - CORRECT ANSWER-maintain a _____ margin of safety from the blade,
This means that you must keep your hands _______ away from the saw blade.
safety glasses - CORRECT ANSWER-wear ______
proper - CORRECT ANSWER-keep the blade guard in the ______ position at all
times
firmly, fence - CORRECT ANSWER-hold stock ____ on the table and against the
____ so it does not shift or kick out when using the miter saw
complete stop - CORRECT ANSWER-after making a cut, but before raising the saw
blade on the miter saw make sure that the blade has come to a ____
under - CORRECT ANSWER-never move your hands _____ the blade, whether it is
moving or not on the miter saw
7 inches - CORRECT ANSWER-all wood scrap goes in the fire pit bin, not the scrap
bin unless it's over _____ long
cross - CORRECT ANSWER-the miter saw will only be used for a type of cut called
______
cutting to fast, board is moving, board not completely pushed back on fence, board is
warped - CORRECT ANSWER-4 main safety concerns for kickback or binding on
the miter saw
miter saw - CORRECT ANSWER-step one in squaring a board
miter saw - CORRECT ANSWER-used for crosscutting wood to rough or exact
length (1/8th inches long)
jointer - CORRECT ANSWER-second step in squaring a board
Jointer - CORRECT ANSWER-used for jointing and edging wood
best - CORRECT ANSWER-joint the _____ edge on your board
adjust - CORRECT ANSWER-do not remove the quard. do not _____ the jointer
without shop teachers permission
1/16th inch - CORRECT ANSWER-maximum cut depth for jointing an edge is _____
, 7 inches, 3/8th inch - CORRECT ANSWER-stock must be at least _____ long to
pass through and at least _____ inches thick on the jointer
with - CORRECT ANSWER-feed the work so that the knives will cut "_____ the
grain" on the jointer (only use new stock that is free of knots , splits and checks)
guard - CORRECT ANSWER-keep your hands away from the cutter head, even
though the ______ is in position on the jointer
4 inches - CORRECT ANSWER-maintain at least a ____ margin of safety. this
means that your hands should always be at least _____ from the cutter head at all
times
knives - CORRECT ANSWER-use a push stick when jointing a flat surface or a
board that is less than 4 inches high. never apply pressure direction over the _____
with your hand
end - CORRECT ANSWER-do not joint _____ grains on the jointer
sharp - CORRECT ANSWER-jointer knives must be _____. dull knives will vibrate
the stock and may cause a kickback
3/8 - CORRECT ANSWER-material cannot be less than ______ thick on the jointer
machine, work area - CORRECT ANSWER-you must clean the ______ and ______
when done with jointer
table saw - CORRECT ANSWER-third step in squaring a board
ripping wood to exact width - CORRECT ANSWER-table saw is used for _________
2nd, parallel - CORRECT ANSWER-rip ______ side on your board ______ to the
jointed edge
towards - CORRECT ANSWER-the table saw blade spins _____ you; this allows you
to control the cut
pushstick - CORRECT ANSWER-use a ______ with smaller stock to protect your
fingers on the table saw
blade guard, important - CORRECT ANSWER-the table saw is equipped with a
_______. this device is the most ____ safety feature for this machine and may not
be removed
This means that you must keep your hands _______ away from the saw blade.
safety glasses - CORRECT ANSWER-wear ______
proper - CORRECT ANSWER-keep the blade guard in the ______ position at all
times
firmly, fence - CORRECT ANSWER-hold stock ____ on the table and against the
____ so it does not shift or kick out when using the miter saw
complete stop - CORRECT ANSWER-after making a cut, but before raising the saw
blade on the miter saw make sure that the blade has come to a ____
under - CORRECT ANSWER-never move your hands _____ the blade, whether it is
moving or not on the miter saw
7 inches - CORRECT ANSWER-all wood scrap goes in the fire pit bin, not the scrap
bin unless it's over _____ long
cross - CORRECT ANSWER-the miter saw will only be used for a type of cut called
______
cutting to fast, board is moving, board not completely pushed back on fence, board is
warped - CORRECT ANSWER-4 main safety concerns for kickback or binding on
the miter saw
miter saw - CORRECT ANSWER-step one in squaring a board
miter saw - CORRECT ANSWER-used for crosscutting wood to rough or exact
length (1/8th inches long)
jointer - CORRECT ANSWER-second step in squaring a board
Jointer - CORRECT ANSWER-used for jointing and edging wood
best - CORRECT ANSWER-joint the _____ edge on your board
adjust - CORRECT ANSWER-do not remove the quard. do not _____ the jointer
without shop teachers permission
1/16th inch - CORRECT ANSWER-maximum cut depth for jointing an edge is _____
, 7 inches, 3/8th inch - CORRECT ANSWER-stock must be at least _____ long to
pass through and at least _____ inches thick on the jointer
with - CORRECT ANSWER-feed the work so that the knives will cut "_____ the
grain" on the jointer (only use new stock that is free of knots , splits and checks)
guard - CORRECT ANSWER-keep your hands away from the cutter head, even
though the ______ is in position on the jointer
4 inches - CORRECT ANSWER-maintain at least a ____ margin of safety. this
means that your hands should always be at least _____ from the cutter head at all
times
knives - CORRECT ANSWER-use a push stick when jointing a flat surface or a
board that is less than 4 inches high. never apply pressure direction over the _____
with your hand
end - CORRECT ANSWER-do not joint _____ grains on the jointer
sharp - CORRECT ANSWER-jointer knives must be _____. dull knives will vibrate
the stock and may cause a kickback
3/8 - CORRECT ANSWER-material cannot be less than ______ thick on the jointer
machine, work area - CORRECT ANSWER-you must clean the ______ and ______
when done with jointer
table saw - CORRECT ANSWER-third step in squaring a board
ripping wood to exact width - CORRECT ANSWER-table saw is used for _________
2nd, parallel - CORRECT ANSWER-rip ______ side on your board ______ to the
jointed edge
towards - CORRECT ANSWER-the table saw blade spins _____ you; this allows you
to control the cut
pushstick - CORRECT ANSWER-use a ______ with smaller stock to protect your
fingers on the table saw
blade guard, important - CORRECT ANSWER-the table saw is equipped with a
_______. this device is the most ____ safety feature for this machine and may not
be removed
