Woodshop test
of the following steps used to square a board, which step is first?
A. Joint a working edge
B. Rip to width
C. Cut one end square
D. Cut to length - CORRECT ANSWER-A. Joint a working edge
Which joint is most commonly used on the corners of a picture frame?
A. Miter
B. Butt
C. Dado
D. Dowel - CORRECT ANSWER-A. Miter
What is a common method used to check for squareness?
A. Measure the circumference
B. Measure diagonally across the corners
C. Measure side to side
D. Measure from top to bottom - CORRECT ANSWER-B. Measure diagonally across
the corners
What standard size of a sheet of plywood?
A. 48" x 96"
B. 24" x 96"
C. 36" x 96"
D. 60" x 96" - CORRECT ANSWER-A. 48" x 96"
When must safety glasses must be worn?
A. Up to the students discretion
B. Only required when operating machines
C. Not required when working with hand tools
D. At all times in the shop - CORRECT ANSWER-D. At all times in the shop
What is a "rip" cut?
A. A cut with the grain
B. A cut which tears the grain
C. A cut across the grain
, D. A cut which is at a 45 degree angle to the grain - CORRECT ANSWER-A. A cut
with the grain
Why is it important to sand with the grain?
A. The sandpaper lasts longer
B. The scratches are less visible
C. Sandpaper is made to sand with the grain
D. It creates less dust - CORRECT ANSWER-B. The scratches are less visible
What happens if excess glue is left on a project?
A. Glue has already absorbed into the wood
B. Glue will dissolve when the stain touches it
C. Stain will cover glue
D. Glue will leave a yellow/white spot - CORRECT ANSWER-D. Glue will leave a
yellow/white spot
Hardwoods come from what kind of trees?
A. Cone bearing
B. Needle bearing
C. Deciduous
D. Coniferous - CORRECT ANSWER-C. Deciduous
What is the Z axis on a CNC machine?
A. Front to back
B. Left to right
C. Diagonal
D. Up and down - CORRECT ANSWER-D. Up and down
What is a plan of procedure?
A. List of materials
B. List of written steps
C. Cost estimate
D. Drawing - CORRECT ANSWER-B. List of written steps
Where can complete information be found on the proper handling of storage of
lacquer and stains
A. Architectural woodworking standards
of the following steps used to square a board, which step is first?
A. Joint a working edge
B. Rip to width
C. Cut one end square
D. Cut to length - CORRECT ANSWER-A. Joint a working edge
Which joint is most commonly used on the corners of a picture frame?
A. Miter
B. Butt
C. Dado
D. Dowel - CORRECT ANSWER-A. Miter
What is a common method used to check for squareness?
A. Measure the circumference
B. Measure diagonally across the corners
C. Measure side to side
D. Measure from top to bottom - CORRECT ANSWER-B. Measure diagonally across
the corners
What standard size of a sheet of plywood?
A. 48" x 96"
B. 24" x 96"
C. 36" x 96"
D. 60" x 96" - CORRECT ANSWER-A. 48" x 96"
When must safety glasses must be worn?
A. Up to the students discretion
B. Only required when operating machines
C. Not required when working with hand tools
D. At all times in the shop - CORRECT ANSWER-D. At all times in the shop
What is a "rip" cut?
A. A cut with the grain
B. A cut which tears the grain
C. A cut across the grain
, D. A cut which is at a 45 degree angle to the grain - CORRECT ANSWER-A. A cut
with the grain
Why is it important to sand with the grain?
A. The sandpaper lasts longer
B. The scratches are less visible
C. Sandpaper is made to sand with the grain
D. It creates less dust - CORRECT ANSWER-B. The scratches are less visible
What happens if excess glue is left on a project?
A. Glue has already absorbed into the wood
B. Glue will dissolve when the stain touches it
C. Stain will cover glue
D. Glue will leave a yellow/white spot - CORRECT ANSWER-D. Glue will leave a
yellow/white spot
Hardwoods come from what kind of trees?
A. Cone bearing
B. Needle bearing
C. Deciduous
D. Coniferous - CORRECT ANSWER-C. Deciduous
What is the Z axis on a CNC machine?
A. Front to back
B. Left to right
C. Diagonal
D. Up and down - CORRECT ANSWER-D. Up and down
What is a plan of procedure?
A. List of materials
B. List of written steps
C. Cost estimate
D. Drawing - CORRECT ANSWER-B. List of written steps
Where can complete information be found on the proper handling of storage of
lacquer and stains
A. Architectural woodworking standards
