If the instructor is out of the room, all power tools and machines must be ________ -
CORRECT ANSWER-off
Adjustments on all power tools and machines must be made before turning on the
_________ - CORRECT ANSWER-machine, power
In case you receive an injury, report it to your ____________ - CORRECT
ANSWER-teacher
Eye protection is required when operating or observing in close proximity all power
activated ____________ - CORRECT ANSWER-machines
When working at the shop tables, all work must be clamped to the table or held
secure in the __________ - CORRECT ANSWER-vise
The shortest length of stock to be run through the planer with safety is _____ -
CORRECT ANSWER-12"
Scraps of lumber must be cleared away from a power machine with a _______ -
CORRECT ANSWER-push stick
All "special" machine setups (resawing, plowing, grooving, dadoing, and tapering)
must be checked by the instructor before turning on the _________ - CORRECT
ANSWER-power panel
To avoid possible injury, students with long hair must wear a headband, hair net,
snoot. or similar device to prevent hair from becoming entangled in ___________ -
CORRECT ANSWER-moving parts
When sanding stock on the disk sander, use only that part of the disk that is traveling
_________ - CORRECT ANSWER-down
Chisels must be hit with a mallet with the chisel facing away from your
____________ - CORRECT ANSWER-body
When crosscutting or ripping stock, you must cover the circular saw blade with a
__________ - CORRECT ANSWER-guard
, The circular saw blade should be raised above the stock to be cut not more than
_________ - CORRECT ANSWER-1/4
When working with tools and machines you must protect your feet and toes by
wearing _________ - CORRECT ANSWER-shoes
Tools with sharp points or ends should be carried with the sharp end pointing
towards the _________ - CORRECT ANSWER-floor
Before leaving the shaper or any other machine for any reason, shut off the power
and wait until the machine has _________ - CORRECT ANSWER-stopped
The purpose of the splitter on the circular saw is to prevent the wood from
_________ - CORRECT ANSWER-binding
Before the operator of a router changes a bit, a cutter, or makes any adjustments, he
or she must disconnect the _________ - CORRECT ANSWER-plug
When turning or sanding on the lathe, the operator must always wear a ________ -
CORRECT ANSWER-face shield
When ripping narrow pieces of stock on the circular saw, you must always use a
_____ or a _____ to keep fingers a safe distance away from the blade (two answers)
- CORRECT ANSWER-push stick or push block
When crosscutting short pieces of stock on the circular saw, you must fasten a
clearance block to the _____ to prevent binding and kick-backs _________ -
CORRECT ANSWER-fence
When face planning on the jointer, allow a minimum stock thickness of _________ -
CORRECT ANSWER-1/2
The shortest length of stock to be run through the Jointer with safety is _________ -
CORRECT ANSWER-12"
When face planning narrow pieces of stock on the jointer, you must always use a
________ - CORRECT ANSWER-push block
CORRECT ANSWER-off
Adjustments on all power tools and machines must be made before turning on the
_________ - CORRECT ANSWER-machine, power
In case you receive an injury, report it to your ____________ - CORRECT
ANSWER-teacher
Eye protection is required when operating or observing in close proximity all power
activated ____________ - CORRECT ANSWER-machines
When working at the shop tables, all work must be clamped to the table or held
secure in the __________ - CORRECT ANSWER-vise
The shortest length of stock to be run through the planer with safety is _____ -
CORRECT ANSWER-12"
Scraps of lumber must be cleared away from a power machine with a _______ -
CORRECT ANSWER-push stick
All "special" machine setups (resawing, plowing, grooving, dadoing, and tapering)
must be checked by the instructor before turning on the _________ - CORRECT
ANSWER-power panel
To avoid possible injury, students with long hair must wear a headband, hair net,
snoot. or similar device to prevent hair from becoming entangled in ___________ -
CORRECT ANSWER-moving parts
When sanding stock on the disk sander, use only that part of the disk that is traveling
_________ - CORRECT ANSWER-down
Chisels must be hit with a mallet with the chisel facing away from your
____________ - CORRECT ANSWER-body
When crosscutting or ripping stock, you must cover the circular saw blade with a
__________ - CORRECT ANSWER-guard
, The circular saw blade should be raised above the stock to be cut not more than
_________ - CORRECT ANSWER-1/4
When working with tools and machines you must protect your feet and toes by
wearing _________ - CORRECT ANSWER-shoes
Tools with sharp points or ends should be carried with the sharp end pointing
towards the _________ - CORRECT ANSWER-floor
Before leaving the shaper or any other machine for any reason, shut off the power
and wait until the machine has _________ - CORRECT ANSWER-stopped
The purpose of the splitter on the circular saw is to prevent the wood from
_________ - CORRECT ANSWER-binding
Before the operator of a router changes a bit, a cutter, or makes any adjustments, he
or she must disconnect the _________ - CORRECT ANSWER-plug
When turning or sanding on the lathe, the operator must always wear a ________ -
CORRECT ANSWER-face shield
When ripping narrow pieces of stock on the circular saw, you must always use a
_____ or a _____ to keep fingers a safe distance away from the blade (two answers)
- CORRECT ANSWER-push stick or push block
When crosscutting short pieces of stock on the circular saw, you must fasten a
clearance block to the _____ to prevent binding and kick-backs _________ -
CORRECT ANSWER-fence
When face planning on the jointer, allow a minimum stock thickness of _________ -
CORRECT ANSWER-1/2
The shortest length of stock to be run through the Jointer with safety is _________ -
CORRECT ANSWER-12"
When face planning narrow pieces of stock on the jointer, you must always use a
________ - CORRECT ANSWER-push block
