OSHA 511 GENERAL INDUSTRY NEWEST 2024 TEST
BANK ACTUAL EXAM COMPLETE 250 QUESTIONS AND
CORRECT DETAILED ANSWERS (VERIFIED ANSWERS) |
ALREADY GRADED A+
Whistle Blower Act - ANSWER: Prohibits discrimination against employees filing
complaints under OSHA or for disclosing safety & health issues concerning the
workplace
Horizontal Standard - ANSWER: A standard which is applied to everyone, across the
board (ex: MSDS, HazComm)
Vertical Standard - ANSWER: A standard that applies to a particular or specific group
of people of industry (ex: welders)
Incorporation By Reference - ANSWER: OSHA Directives Compliance Directives
GUIDEBOOK
● Enforcement & Compliance Directives (CPL)
● Letters of Interpretation
● Federal Register
CPL - ANSWER: Compliance....
Floor Hole - ANSWER: Opening greater than 1in & less than 12in in any floor,
platform, pavement or yard, through which materials (but not persons) may fall
through (ex: belt hole, pipe opening or slot opening)
Floor Opening - ANSWER: Opening greater than 12in (note an OPENING is larger than
a HOLE)
Minimum width of fixed industrial stairs - ANSWER: 28 inches wide
OSHA certifies that a citation must be - ANSWER: ● addressed
● corrections must be completed by abatement date
● OSHA has 180 days to issue the actual citation(s)
Cages or Wells shall be provided on ladders - ANSWER: greater than 20 feet to a
maximum of unbroken length of 30 feet (1910.27)
General Duty Clause - ANSWER: Every employer shall furnish to his employee's
employment and a place of employment which are free from recognized hazards
that are causing or likely to cause death or serious physical harm to his employees.
OSHA Inspection Review (priority) - ANSWER: 1) Imminent danger
2) Catastrophies & fatal accidents
, 3) Employee complaints & referrals
4) Programmed, high level inspections
5) Follow up inspections
Inspection Process must include - ANSWER: 1) Opening Conference
2) Walk Around
3) Closing Conference
Creating Employee - ANSWER: One who creates & exposes an employee to hazard(s)
When is a Fit Test required? - ANSWER: If voluntary respirator use is permissible,
then user must read & sign Appendix D
Hazcom 1983 - ANSWER: grants workers' RIGHT TO KNOW (RTK)
Hazcom 2012 - ANSWER: grants workers' RIGHT TO UNDERSTAND (RTU)
3 Hazard Groups in Hazard Classification - ANSWER: 1) Physical
2) Health
3) Environmental
Flammable - ANSWER: Flash Point is below 73°F
Combustible - ANSWER: Flash Point is higher than 73°F
Hazard Classification Process is divided into - ANSWER: 3 Hazard Groups
1) Physical
2) Health
3) Environmental
OSHA Mission - ANSWER: "To protect the health & safety of American workers"
Danger (signal word) - ANSWER: a more severe hazard
Warning (signal word) - ANSWER: a less severe hazard
When is Fit Testing for Respirators required? - ANSWER: When a respirator is
required to be worn
When establishing Hazard Controls, what is the 1st priority? - ANSWER: Engineering
Controls
Question #26 - ANSWER: answer is C (Dana)
Question #46 - ANSWER: answer is A
"failure to completely tagout"
BANK ACTUAL EXAM COMPLETE 250 QUESTIONS AND
CORRECT DETAILED ANSWERS (VERIFIED ANSWERS) |
ALREADY GRADED A+
Whistle Blower Act - ANSWER: Prohibits discrimination against employees filing
complaints under OSHA or for disclosing safety & health issues concerning the
workplace
Horizontal Standard - ANSWER: A standard which is applied to everyone, across the
board (ex: MSDS, HazComm)
Vertical Standard - ANSWER: A standard that applies to a particular or specific group
of people of industry (ex: welders)
Incorporation By Reference - ANSWER: OSHA Directives Compliance Directives
GUIDEBOOK
● Enforcement & Compliance Directives (CPL)
● Letters of Interpretation
● Federal Register
CPL - ANSWER: Compliance....
Floor Hole - ANSWER: Opening greater than 1in & less than 12in in any floor,
platform, pavement or yard, through which materials (but not persons) may fall
through (ex: belt hole, pipe opening or slot opening)
Floor Opening - ANSWER: Opening greater than 12in (note an OPENING is larger than
a HOLE)
Minimum width of fixed industrial stairs - ANSWER: 28 inches wide
OSHA certifies that a citation must be - ANSWER: ● addressed
● corrections must be completed by abatement date
● OSHA has 180 days to issue the actual citation(s)
Cages or Wells shall be provided on ladders - ANSWER: greater than 20 feet to a
maximum of unbroken length of 30 feet (1910.27)
General Duty Clause - ANSWER: Every employer shall furnish to his employee's
employment and a place of employment which are free from recognized hazards
that are causing or likely to cause death or serious physical harm to his employees.
OSHA Inspection Review (priority) - ANSWER: 1) Imminent danger
2) Catastrophies & fatal accidents
, 3) Employee complaints & referrals
4) Programmed, high level inspections
5) Follow up inspections
Inspection Process must include - ANSWER: 1) Opening Conference
2) Walk Around
3) Closing Conference
Creating Employee - ANSWER: One who creates & exposes an employee to hazard(s)
When is a Fit Test required? - ANSWER: If voluntary respirator use is permissible,
then user must read & sign Appendix D
Hazcom 1983 - ANSWER: grants workers' RIGHT TO KNOW (RTK)
Hazcom 2012 - ANSWER: grants workers' RIGHT TO UNDERSTAND (RTU)
3 Hazard Groups in Hazard Classification - ANSWER: 1) Physical
2) Health
3) Environmental
Flammable - ANSWER: Flash Point is below 73°F
Combustible - ANSWER: Flash Point is higher than 73°F
Hazard Classification Process is divided into - ANSWER: 3 Hazard Groups
1) Physical
2) Health
3) Environmental
OSHA Mission - ANSWER: "To protect the health & safety of American workers"
Danger (signal word) - ANSWER: a more severe hazard
Warning (signal word) - ANSWER: a less severe hazard
When is Fit Testing for Respirators required? - ANSWER: When a respirator is
required to be worn
When establishing Hazard Controls, what is the 1st priority? - ANSWER: Engineering
Controls
Question #26 - ANSWER: answer is C (Dana)
Question #46 - ANSWER: answer is A
"failure to completely tagout"
