MCC-NH Gas Fitters Exam
Questions and Answers 100%
Correct
What is the minimum percentage needed to pass a written test for each
specialty license? - ANSWER-70%
How many hours of educational training are required for the third specialty
license? - ANSWER-140 Hours (Safemec 305.04)
How many hours of on-job-training are required for the third specialty
license? - ANSWER-2000 On Job Training Hour (Safemec 305.04)
How much does the initial fuel gas trainee license cost? - ANSWER-$90.00
What is the second tier to the specialty license? - ANSWER-Fuel Gas
Installation Technician
,How many hours of educational training are required for the second specialty
license? - ANSWER-100 Hours Total (Safemec 305.03)
How many hours of on-job-training are required for the second specialty
license? - ANSWER-1000 On Job Training Hours (Safemec 305.03)
What is the third tier to the specialty license? - ANSWER-Fuel Gas Service
Technician
How much does the initial fuel gas trainee renewal cost? - ANSWER-$80.00
How many years is a license active before expiration? - ANSWER-2 Years
When does a license expire? - ANSWER-At the end of the birth month
What is the first tier to the specialty license? - ANSWER-Gas Piping Installer
How many hours of educational training are required for the first specialty
license? - ANSWER-60 Hours (Safemec 305.02)
, How many hours of on-job-training are required for the first specialty license?
- ANSWER-1000 Hours (Safemec 305.02)
How many questions at minimum are required on each specialty license
test? - ANSWER-100
What code covers the 1st and 2nd stage regulators on a LP system? -
ANSWER-NFPA58
A gas piping system was installed per code requirements in 2000, and now
due to new or revised code material it no longer meets code, we shall we do?
- ANSWER-Contact the AHJ (it may fall under reciprocity)
Which table shall be referenced to design a gas piping system to have no
more than a, .5" W.C. pressure drop for the following conditions; LP gas, 11"
W.C. available supply pressure and black iron pipe? - ANSWER-6.3.1(D)
Which Table shall be referenced to design a gas piping system to have no
more than a .5" W.C. pressure drop for the following conditions; LP gas, 11"
W.C. available supply pressure and soft copper tubing? - ANSWER-6.3.1(F)
Questions and Answers 100%
Correct
What is the minimum percentage needed to pass a written test for each
specialty license? - ANSWER-70%
How many hours of educational training are required for the third specialty
license? - ANSWER-140 Hours (Safemec 305.04)
How many hours of on-job-training are required for the third specialty
license? - ANSWER-2000 On Job Training Hour (Safemec 305.04)
How much does the initial fuel gas trainee license cost? - ANSWER-$90.00
What is the second tier to the specialty license? - ANSWER-Fuel Gas
Installation Technician
,How many hours of educational training are required for the second specialty
license? - ANSWER-100 Hours Total (Safemec 305.03)
How many hours of on-job-training are required for the second specialty
license? - ANSWER-1000 On Job Training Hours (Safemec 305.03)
What is the third tier to the specialty license? - ANSWER-Fuel Gas Service
Technician
How much does the initial fuel gas trainee renewal cost? - ANSWER-$80.00
How many years is a license active before expiration? - ANSWER-2 Years
When does a license expire? - ANSWER-At the end of the birth month
What is the first tier to the specialty license? - ANSWER-Gas Piping Installer
How many hours of educational training are required for the first specialty
license? - ANSWER-60 Hours (Safemec 305.02)
, How many hours of on-job-training are required for the first specialty license?
- ANSWER-1000 Hours (Safemec 305.02)
How many questions at minimum are required on each specialty license
test? - ANSWER-100
What code covers the 1st and 2nd stage regulators on a LP system? -
ANSWER-NFPA58
A gas piping system was installed per code requirements in 2000, and now
due to new or revised code material it no longer meets code, we shall we do?
- ANSWER-Contact the AHJ (it may fall under reciprocity)
Which table shall be referenced to design a gas piping system to have no
more than a, .5" W.C. pressure drop for the following conditions; LP gas, 11"
W.C. available supply pressure and black iron pipe? - ANSWER-6.3.1(D)
Which Table shall be referenced to design a gas piping system to have no
more than a .5" W.C. pressure drop for the following conditions; LP gas, 11"
W.C. available supply pressure and soft copper tubing? - ANSWER-6.3.1(F)
