EXTREME SWITCH & ROUTING/FUNDAMENTALS
CERTS.
What is the default value for the RIP garbagetime setting? - Answers-120 seconds
Given router interfaces 10.0.0.1/24, 10.10.10.10/24, 192.168.0.1/24, and
192.168.255.254/24 on a Summit7i switch what will be the OSPF router ID given the
following command: config ospf routerid automatic? - Answers-192.168.255.254/24
Which command would you use to configure VLAN corporate with IP address
192.168.0.1/16? - Answers-config vlan corporate ipaddress 192.168.0.1/16
VLAN aggregation allows multiple sub-VLANs to share a single IP subnet. - Answers-
True
How do you disable Split Horizon? - Answers-Disable rip splithorizon
Name a relative route priority that cannot be altered? - Answers-Direct
Given this display, how would you find information similar to the SHOW SWITCH
command? - Answers-Click on STATISTICS, then SWITCH.
Internal routers within an OSPF area are either DRs, BDRs, or... - Answers-ODR
STPDs s0, s1, and s2 have been created. How would you activate only s1 while
leaving the other STPDs inactive? - Answers-enable stpd s1
SNMP access to ExtremeWare can be limited by the following methods: - Answers-Use
an access list, use an access profile, use the disable snmp access command
Which ExtremeWare feature permits ESRP to increase the number of protected
VLANs by placing them under the control of a master VLAN? - Answers-ESRP domains
Which command would you use to configure VLAN CORPORATE (tag 100) with
ports 1:1 through 4:8 tagged and ports 5:1 through 8:8 as untagged? - Answers-config
vlan corporate add ports 1:1-4:8 tagged
config vlan corporate add ports 5:1-8:8 untagged
How would you change the password for John Doe's management account? - Answers-
Enter config account jdoe and then enter the new password twice.
What is the minimum ExtremeWare software version that supports the Summit48i? -
Answers-ExtremeWare 6.x
, When using Spanning Tree Protocol, ExtremeWare permits VLANs in different
STPDs to share the same port when tagged. - Answers-False
What is the default STP forward delay value? - Answers-15 seconds
Which of the following routes will be used to forward a frame to 192.168.1.174? -
Answers-192.168.1.128/25
Which RIP settings are enabled by default? - Answers-Triggered updates, Poison
Reverse, or Split Horizon
If a packet to be forwarded does not match existing flow information in the ASIC
route cache, the packet is queued to the __________ for route processing. - Answers-
CPU
All OSPF routers in the same area must have the same LSDB. - Answers-True
In RIP, poison reverse means that: - Answers-A route is advertised as unreachable to
the interface from which it was learned.
What type of area is used to limit external routes? - Answers-Stub area
RIP version 2 uses a composite metric that includes link speed and delay. - Answers-
False
A VLAN can be a member of up to 64 STPDs. - Answers-False
Unlike VRRP, the Extreme Standby Router Protocol provides redundancy at both
the data link and network layers. - Answers-True
Which of the following is not advertised in an OSPF Link State Advertisement? -
Answers-Link utilization
__________ allow(s) multiple VLANs to be controlled by a single ESRP instance. -
Answers-ESRP domains
Extreme Networks "I" series switches have this many queues per port. - Answers-8
Without QoS, all packets are allowed equal access to an egress port. - Answers-True
QoS policy is applied _____ in an Extreme switch. - Answers-per queue, per port
An Extreme Switch is shipped with a pre-configured VLAN called DEFAULT that has all
switch
ports as tagged members. - Answers-False
CERTS.
What is the default value for the RIP garbagetime setting? - Answers-120 seconds
Given router interfaces 10.0.0.1/24, 10.10.10.10/24, 192.168.0.1/24, and
192.168.255.254/24 on a Summit7i switch what will be the OSPF router ID given the
following command: config ospf routerid automatic? - Answers-192.168.255.254/24
Which command would you use to configure VLAN corporate with IP address
192.168.0.1/16? - Answers-config vlan corporate ipaddress 192.168.0.1/16
VLAN aggregation allows multiple sub-VLANs to share a single IP subnet. - Answers-
True
How do you disable Split Horizon? - Answers-Disable rip splithorizon
Name a relative route priority that cannot be altered? - Answers-Direct
Given this display, how would you find information similar to the SHOW SWITCH
command? - Answers-Click on STATISTICS, then SWITCH.
Internal routers within an OSPF area are either DRs, BDRs, or... - Answers-ODR
STPDs s0, s1, and s2 have been created. How would you activate only s1 while
leaving the other STPDs inactive? - Answers-enable stpd s1
SNMP access to ExtremeWare can be limited by the following methods: - Answers-Use
an access list, use an access profile, use the disable snmp access command
Which ExtremeWare feature permits ESRP to increase the number of protected
VLANs by placing them under the control of a master VLAN? - Answers-ESRP domains
Which command would you use to configure VLAN CORPORATE (tag 100) with
ports 1:1 through 4:8 tagged and ports 5:1 through 8:8 as untagged? - Answers-config
vlan corporate add ports 1:1-4:8 tagged
config vlan corporate add ports 5:1-8:8 untagged
How would you change the password for John Doe's management account? - Answers-
Enter config account jdoe and then enter the new password twice.
What is the minimum ExtremeWare software version that supports the Summit48i? -
Answers-ExtremeWare 6.x
, When using Spanning Tree Protocol, ExtremeWare permits VLANs in different
STPDs to share the same port when tagged. - Answers-False
What is the default STP forward delay value? - Answers-15 seconds
Which of the following routes will be used to forward a frame to 192.168.1.174? -
Answers-192.168.1.128/25
Which RIP settings are enabled by default? - Answers-Triggered updates, Poison
Reverse, or Split Horizon
If a packet to be forwarded does not match existing flow information in the ASIC
route cache, the packet is queued to the __________ for route processing. - Answers-
CPU
All OSPF routers in the same area must have the same LSDB. - Answers-True
In RIP, poison reverse means that: - Answers-A route is advertised as unreachable to
the interface from which it was learned.
What type of area is used to limit external routes? - Answers-Stub area
RIP version 2 uses a composite metric that includes link speed and delay. - Answers-
False
A VLAN can be a member of up to 64 STPDs. - Answers-False
Unlike VRRP, the Extreme Standby Router Protocol provides redundancy at both
the data link and network layers. - Answers-True
Which of the following is not advertised in an OSPF Link State Advertisement? -
Answers-Link utilization
__________ allow(s) multiple VLANs to be controlled by a single ESRP instance. -
Answers-ESRP domains
Extreme Networks "I" series switches have this many queues per port. - Answers-8
Without QoS, all packets are allowed equal access to an egress port. - Answers-True
QoS policy is applied _____ in an Extreme switch. - Answers-per queue, per port
An Extreme Switch is shipped with a pre-configured VLAN called DEFAULT that has all
switch
ports as tagged members. - Answers-False
