CIP Level 1 NACE-CIP1-001 Practice quiz With Real
Questions (Latest )
You are the NACE inspector on a tank lining project where a 50% solids epoxy tank
lining is being applied. After application of the 19 coat, you notice small blisters in
some areas of the applied lining. Your FIRST preferred course of action is to:
A. Break the blisters to see what's inside
B. Document the problem and advise the contractor and owner's representative
C. Document the problem and advise the contractor
D. Extract any liquid that may be inside the blister and sent it to the lab for further
analysis. - ANSWER: Document the problem and advise the contractor and owner's
representative
The dew point is the temperature at which
A. Water freezes
B. humidity decreases
C. Condensation occurs
D. the air is saturated - ANSWER: condensation occurs
If a contractor is using a poorly maintained compressor to supply air for abrasive
blast cleaning and conventional airspray, the coating inspector should perform a
A. dry film thickness (DEI) measurement
B. wet film thickness (WFT) measurement
C. blotter test for the presence of oil and water
D. vial test - ANSWER: blotter test for the presence of oil and water
Upon arrival of coating materials, the inspector should
A. review coating contractors' plans for storage of coating materials and confirm
they meet national, local, and owners' fire and environmental regulations
B. observe and document the amount material and batch numbers
C. observe aryl document that the applicator WFT at regular intervals during
application
D. observe and document time frame and environmental conditions between each
coat - ANSWER: observe and document the amount material and batch numbers
Relative humidity is
A. a measure of the amount of moisture in the air compared to saturation level
B. a measure of the amount of moisture in the air compared to the air temperature
C. the lowest temperature at which moisture forms on a steel surface
D. the highest temperature at which moisture forms on a steel surface - ANSWER: a
measure of the amount of moisture in the air compared to saturation level
Galvanic corrosion occurs on which of the following substrates:
A. concrete
B. fiberglass reinforced plastic
C. metal
,D. wood - ANSWER: metal
When applying Thermal spray coatings, the specification is most likely to reference:
A. SSPC PA 2
B. NACE SP 0178
C. NACE SP 0188
D. SSPC-CS 23.00/AWS C2.23/NACE No.12 - ANSWER: SSPC-CS 23.00/AWS
C2.23/NACE No.12
What is the minimum recommended distance away from an edge that an inspector
should take measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT)
gauge?
A. 1 cm (.39in)
B. 2.5cm (1 in)
C. 6.35cm (2.5 in)
D. 2.5 millimeters (.10 in) - ANSWER: 2.5cm (1 in)
Polymerization is the process of:
A. monomers telegraphing
B. monomers joining together
C. All thermoplastic coatings
D. All organic coatings - ANSWER: monomers joining together
An exposed area of the substrate or previous coat of a conduction coating material,
often caused by poor application technique is called:
A. cracking
B. sagging
C. holiday
D. checking - ANSWER: holiday
Checking is:
A. an exposed area of the substrate or previous coat material, caused by poor
application technique
B. a fine crack in the surface of a coating that rarely reaches the substrate
C. a very small hole in a coating caused when air or solvent is trapped in porous film
and then escapes
D. surface breaks in the film that often result from grease or oil contamination and
revel the substrate - ANSWER: a fine crack in the surface of a coating that rarely
reaches the substrate
Inspection documentation is important because:
A. it is the only deliverable item provided by the inspector
B. owners use the documentation for a variety of purposes
C. (A) only
D. (A) and (B) - ANSWER: owners use the documentation for a variety of purposes
An inspector's personal log book should contain:
, A. subjective comments regarding the application team
B. objective comments regarding the application work
C. no comments regarding the application team
D. the inspector's personal opinions of the application team - ANSWER: no
comments regarding the application team
You have just received your NACE CIP Level 1 Certification when you are asked to
supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course
of action is to:
A. accept the assignment without hesitation
B. advise the prospective employer that you cannot accept the position
C. meet with the prospective employer to determine the scope of your role
D. Review the NACE Attestation prior to making a decision - ANSWER: meet with the
prospective employer to determine the scope of your role
Good records can provide maintenance departments with detailed information
about ALL of the following EXCEPT
A. what items were coated
B. what materials were used
C. when the coating will be reapplied
D. how the item was coated - ANSWER: when the coating will be reapplied
Non Conformance Reports are completed by the inspector:
A. in every instance that an item does not meet the specification requirements
B. When the inspector deems it to be a significant non-conforming item
C. when the inspector and contractor deem it to be a significant non-conforming
item
D. in accordance with the specification's definition of a non-conformance - ANSWER:
when the inspector and contractor deem it to be a significant non-conforming item
The initial steel condition is important to the NACE inspector because -
A. if the steel is pitted, more coating will be required
B. Less abrasive is need if the mill Scale s gone
C. it affects the final appearance after blasting
D. the inspector may have to reject the steel - ANSWER: the inspector may have to
reject the steel
The form of corrosion that has the largest potential for unexpected catastrophic
failure is:
A. general corrosion
B. atmospheric corrosion
C. galvanic corrosion
D. localized corrosion - ANSWER: localized corrosion
What is used to determine compressed air cleanliness?
A. needle pressure grade
B. psychrometer
Questions (Latest )
You are the NACE inspector on a tank lining project where a 50% solids epoxy tank
lining is being applied. After application of the 19 coat, you notice small blisters in
some areas of the applied lining. Your FIRST preferred course of action is to:
A. Break the blisters to see what's inside
B. Document the problem and advise the contractor and owner's representative
C. Document the problem and advise the contractor
D. Extract any liquid that may be inside the blister and sent it to the lab for further
analysis. - ANSWER: Document the problem and advise the contractor and owner's
representative
The dew point is the temperature at which
A. Water freezes
B. humidity decreases
C. Condensation occurs
D. the air is saturated - ANSWER: condensation occurs
If a contractor is using a poorly maintained compressor to supply air for abrasive
blast cleaning and conventional airspray, the coating inspector should perform a
A. dry film thickness (DEI) measurement
B. wet film thickness (WFT) measurement
C. blotter test for the presence of oil and water
D. vial test - ANSWER: blotter test for the presence of oil and water
Upon arrival of coating materials, the inspector should
A. review coating contractors' plans for storage of coating materials and confirm
they meet national, local, and owners' fire and environmental regulations
B. observe and document the amount material and batch numbers
C. observe aryl document that the applicator WFT at regular intervals during
application
D. observe and document time frame and environmental conditions between each
coat - ANSWER: observe and document the amount material and batch numbers
Relative humidity is
A. a measure of the amount of moisture in the air compared to saturation level
B. a measure of the amount of moisture in the air compared to the air temperature
C. the lowest temperature at which moisture forms on a steel surface
D. the highest temperature at which moisture forms on a steel surface - ANSWER: a
measure of the amount of moisture in the air compared to saturation level
Galvanic corrosion occurs on which of the following substrates:
A. concrete
B. fiberglass reinforced plastic
C. metal
,D. wood - ANSWER: metal
When applying Thermal spray coatings, the specification is most likely to reference:
A. SSPC PA 2
B. NACE SP 0178
C. NACE SP 0188
D. SSPC-CS 23.00/AWS C2.23/NACE No.12 - ANSWER: SSPC-CS 23.00/AWS
C2.23/NACE No.12
What is the minimum recommended distance away from an edge that an inspector
should take measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT)
gauge?
A. 1 cm (.39in)
B. 2.5cm (1 in)
C. 6.35cm (2.5 in)
D. 2.5 millimeters (.10 in) - ANSWER: 2.5cm (1 in)
Polymerization is the process of:
A. monomers telegraphing
B. monomers joining together
C. All thermoplastic coatings
D. All organic coatings - ANSWER: monomers joining together
An exposed area of the substrate or previous coat of a conduction coating material,
often caused by poor application technique is called:
A. cracking
B. sagging
C. holiday
D. checking - ANSWER: holiday
Checking is:
A. an exposed area of the substrate or previous coat material, caused by poor
application technique
B. a fine crack in the surface of a coating that rarely reaches the substrate
C. a very small hole in a coating caused when air or solvent is trapped in porous film
and then escapes
D. surface breaks in the film that often result from grease or oil contamination and
revel the substrate - ANSWER: a fine crack in the surface of a coating that rarely
reaches the substrate
Inspection documentation is important because:
A. it is the only deliverable item provided by the inspector
B. owners use the documentation for a variety of purposes
C. (A) only
D. (A) and (B) - ANSWER: owners use the documentation for a variety of purposes
An inspector's personal log book should contain:
, A. subjective comments regarding the application team
B. objective comments regarding the application work
C. no comments regarding the application team
D. the inspector's personal opinions of the application team - ANSWER: no
comments regarding the application team
You have just received your NACE CIP Level 1 Certification when you are asked to
supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course
of action is to:
A. accept the assignment without hesitation
B. advise the prospective employer that you cannot accept the position
C. meet with the prospective employer to determine the scope of your role
D. Review the NACE Attestation prior to making a decision - ANSWER: meet with the
prospective employer to determine the scope of your role
Good records can provide maintenance departments with detailed information
about ALL of the following EXCEPT
A. what items were coated
B. what materials were used
C. when the coating will be reapplied
D. how the item was coated - ANSWER: when the coating will be reapplied
Non Conformance Reports are completed by the inspector:
A. in every instance that an item does not meet the specification requirements
B. When the inspector deems it to be a significant non-conforming item
C. when the inspector and contractor deem it to be a significant non-conforming
item
D. in accordance with the specification's definition of a non-conformance - ANSWER:
when the inspector and contractor deem it to be a significant non-conforming item
The initial steel condition is important to the NACE inspector because -
A. if the steel is pitted, more coating will be required
B. Less abrasive is need if the mill Scale s gone
C. it affects the final appearance after blasting
D. the inspector may have to reject the steel - ANSWER: the inspector may have to
reject the steel
The form of corrosion that has the largest potential for unexpected catastrophic
failure is:
A. general corrosion
B. atmospheric corrosion
C. galvanic corrosion
D. localized corrosion - ANSWER: localized corrosion
What is used to determine compressed air cleanliness?
A. needle pressure grade
B. psychrometer
