CWB 2 ALL MODULES EXAM 2024 NEWEST ACTUAL EXAM COMPLETE 250 QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED ANSWERS) |ALREADY GRADED A+ // BRAND NEW!!

CWB 2 ALL MODULES EXAM 2024 NEWEST ACTUAL EXAM COMPLETE 250 QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED ANSWERS) |ALREADY GRADED A+ // BRAND NEW!! A Plasma is: A) A gas made up of positive ions and free electrons B) A liquid used to reduce adherence of spatter C) The main component in an inverter power source D) Always present in an electrical circuit - A) A gas made up of positive ions and free electrons To increase melting rate (burn-off rate) in the shielded metal arc welding (SMAW) process, which polarity should be used? A) DCEP B) ACEP C) DCEN D) ACEP - C) DCEN Which type of welding power source is used for the SMAW process? A) Constant Current Page 2/31 Crafted for Academic Insight by ©Olivia GreenWays 2025. All rights reserved. B) Constant Voltage C) Pulsed Current D) Pulsed Voltage - A) Constant Current The purpose of a drooping welding power source is to produce: A) Constant voltage regardless of the current demand B) Constant arc length regardless of current C) Nearly constant current regardless of voltage fluctuations B) Low open circuit voltage - C) Nearly constant current regardless of voltage fluctuations A self-regulating welding arc is produced by a: A) Constant current power source with a constant speed wire feed system B) Constant voltage power source with a voltage sensing wire feed system C) Constant current power source D) Constant voltage power source with a constant speed wire feed system - D) Constant voltage power source with a constant speed wire feed system Short circuit current is determined by the: A) Voltage in the circuit B) Static characteristic of the power source Page 3/31 Crafted for Academic Insight by ©Olivia GreenWays 2025. All rights reserved. C) Position of welding D) Skill of the welder - B) Static characteristic of the power source A Transformer is a device that: A) Transforms AC to DC B) Works only to change a DC voltage C) Changes the value of an AC voltage but does not change the frequency D) Is made from a semiconductor - C) Changes the value of an AC voltage but does not change the frequency A Rectifier is a device that converts: A) DC current to AC current B) AC Current to a high value DC current C) DC current to a high value DC current D) AC current to DC current - D) AC current to DC current Microprocessor controls are used in the more modern welding power sources to: A) Provide more sophisticated levels of control for the welding system B) Allow welding variables to be stored for use later C) Provide feedback control Page 4/31 Crafted for Academic Insight by ©Olivia GreenWays 2025. All rights reserved. D) All of the above - D) All of the above Inverter welding power sources provide increased control over the welding arc because they: A) Utilize feedback control B) Can respond very quickly to correct any changed in the welding circuits C) Can utilize advanced pulsed waveforms to allow out of position welding using spray transfer D) All of the above - D) All of the above It would be correct to say: A) Expansion and contraction are proportional to the dimensions of the heated area B) When a bar is heated under restraint, its stress relieves itself as it cools C) Slow cooling of a heated area will provide the greatest amount of shrinkage D) When metal is heated it expands, but it does not shrink back to its original size when it cools - A) Expansion and contraction are proportional to the dimensions of the heated area To reduce the amount of angular distortion you should: A) Increase the travel speed B) Reduce the angle of preparation C) Pre-heat the metal D) All of the above Page 5/31 Crafted for Academic Insight by ©Olivia GreenWays 2025. All rights reserved. E) None of the above - D) All of the above When a structural member has been bent sharply, it can be straightened by heating: A) A vee shaped section of the web underneath the bent area of the flange B) The inside corner of an angle, channel, i-beam, or T bar C) A vee shaped area at the point of the greatest bend, with the top of the vee at the point of greatest bend D) All along the edge of the section E) All along the edge opposite of the one which is bent - C) A vee shaped area at the point of the greatest bend, with the top of the vee at the point of greatest bend Of the many mechanical means of controlling distortion, the following will have the least residual stress: A) Rigid clamping B) Subassembly of the sections C) Heavy strongbacks, welded on both sides of the joint D) Similar weldments clamped back to back E) Pre-set the plates to allow recovery of angular distortion - E) Pre-set the plates to allow recovery