BIPC 620 / ACTUAL
EXAM QUESTIONS
AND CORRECT
DETAILED ANSWERS
(VERIFIED ANSWERS)
Certified IPC Trainter CIT and 2 Years
Certified IPC Specilist
certifications exipre after
how many years
Master IPC Trainers MIT are CIT and CIS only
authorized to ceritfy
A CIT is authorized to ceritfy CIS
90 days
If permitted by company
policy, a CIT may grant an
extension of up to how
many days
Practice questions for this set
Learn
Studied 7 terms
Nice work, you're crushing it
Continue studying in Learn
Terms in this set (131)
,What module is required as a Module 1
pre req. for IPC 620
CIS certification
CIS retesting may be taken 24 hours
only after a minimum of
What is the correct order of Design, PCB Fabrication, Assemly, Cleaning and
production status Coating
The tolerance for Plus or Minus 15 (Chapter 1) Page 1-7
magnification aid is
The Manufacturer shall N1D2D3 - PAGE 1-8
(_1_2_3) have a documented
calibration system
What is a Process A condition that identifies a characteristics that does not
Indicator affect the form fit or function of a product- should be
monitored
Conditions that are not Acceptable - Page 1-4
specified as defective or as a
process indicator are
considered
Illumination at the surface 1000 lm/m^2 or 93 foot candles
of workstation should be
minimum of
A condition that is close to Target
perfect defines what type of
condition
1.5X-3X - Table 1-1
When inspecting a 22 AWG
wire the inspection
magnification range shall be
, The criteria defined in IPC- Class 1- General Electronic Products
620 reflect three product Class 2- Dedicated Service Electronic Products
classes , Class 1, 2, Class 3- High Performance/ Harsh Environment
3 Electronic Products
If insulation thickness is Defect for all classes - Chapter 3 - page 3-9
reduced by more than
20%, the condition is _1_2_3
Damaged wires that do A1P2P3 so process indicators for 2 and 3 -Page 3-2
not exceed the limits
specified in table 3-1 are
considered _1_2_3
Wire separation that exceeds A1P2D3 Chapter 3 page 3-6
one strand diameter but
does not extend beyond the
wire insulation outside
diameter is _1_2_3
The maximum number of 0 - Chapter 3, refer to Table 3-1
damaged strands for Class 2
wires with 28 strands used at
a potential of 6kV or greater
is
Defect
Insulation that has been
charred, melted into the wire
strands and has uneven or
ragged pieces of insulation
that is greater than 50% of
the outside diameter or 1
mm, is what for all classes
EXAM QUESTIONS
AND CORRECT
DETAILED ANSWERS
(VERIFIED ANSWERS)
Certified IPC Trainter CIT and 2 Years
Certified IPC Specilist
certifications exipre after
how many years
Master IPC Trainers MIT are CIT and CIS only
authorized to ceritfy
A CIT is authorized to ceritfy CIS
90 days
If permitted by company
policy, a CIT may grant an
extension of up to how
many days
Practice questions for this set
Learn
Studied 7 terms
Nice work, you're crushing it
Continue studying in Learn
Terms in this set (131)
,What module is required as a Module 1
pre req. for IPC 620
CIS certification
CIS retesting may be taken 24 hours
only after a minimum of
What is the correct order of Design, PCB Fabrication, Assemly, Cleaning and
production status Coating
The tolerance for Plus or Minus 15 (Chapter 1) Page 1-7
magnification aid is
The Manufacturer shall N1D2D3 - PAGE 1-8
(_1_2_3) have a documented
calibration system
What is a Process A condition that identifies a characteristics that does not
Indicator affect the form fit or function of a product- should be
monitored
Conditions that are not Acceptable - Page 1-4
specified as defective or as a
process indicator are
considered
Illumination at the surface 1000 lm/m^2 or 93 foot candles
of workstation should be
minimum of
A condition that is close to Target
perfect defines what type of
condition
1.5X-3X - Table 1-1
When inspecting a 22 AWG
wire the inspection
magnification range shall be
, The criteria defined in IPC- Class 1- General Electronic Products
620 reflect three product Class 2- Dedicated Service Electronic Products
classes , Class 1, 2, Class 3- High Performance/ Harsh Environment
3 Electronic Products
If insulation thickness is Defect for all classes - Chapter 3 - page 3-9
reduced by more than
20%, the condition is _1_2_3
Damaged wires that do A1P2P3 so process indicators for 2 and 3 -Page 3-2
not exceed the limits
specified in table 3-1 are
considered _1_2_3
Wire separation that exceeds A1P2D3 Chapter 3 page 3-6
one strand diameter but
does not extend beyond the
wire insulation outside
diameter is _1_2_3
The maximum number of 0 - Chapter 3, refer to Table 3-1
damaged strands for Class 2
wires with 28 strands used at
a potential of 6kV or greater
is
Defect
Insulation that has been
charred, melted into the wire
strands and has uneven or
ragged pieces of insulation
that is greater than 50% of
the outside diameter or 1
mm, is what for all classes
