Page | 1
CSA W47.1 AND CSA W59 EXAM 2025|
BRAND NEW ACTUAL EXAM WITH 100%
VERIFIED QUESTIONS AND CORRECT
SOLUTIONS| GUARANTEED VALUE PACK|
ACE YOUR GRADES.
When any examination indicates the presence of a planer edge
discontinuity
greater than 25 mm in depth, the_______shall refrain from any
immediate remedial work - correct answer - erector
For spot radiographic examination of welds, each spot
radiography should
show at least_________of weld length with the weld image
centered on the spot. - correct answer - 100 mm
All members and welds affected by the work shall be visually
inspected in
accordance with: - correct answer - the engineer's comprehensive
plan
, Page | 2
When application of heat is used to curve or straighten a product,
the
maximum temperature of heated areas, as measured by
approved methods, shall not exceed ________ for quenched and
tempered steels - correct answer - 590°C
When the base metal temperature is below 0°C, the base metal
shall be
preheated to at least ________and this temperature maintained
during
welding - correct answer - 10°C
For G40.21, 700QT steel 42 mm thick, the maximum preheat and
interpass
temperature shall not exceed: - correct answer - 230°C
The hole-type image quality indicator (IQI) designation, film side,
required
for ASTM A517M steel plate, 12 mm thick: - correct answer - 12
, Page | 3
Extension bars, run-off plates and backing, shall be of the same
material as the base material, for the welding of steels with a
minimum specified tensile
strength of: - correct answer - >480MPa
To establish appropriate safety and health practices and to
determine the
applicability of regulatory limitations prior to use, it is the
responsibility of: - correct answer - the user of this standard
(W59)
The filler metal for exposed bare applications of CSA 040.21-
ASTM A 242
Steel, for application to cyclically loaded structures, deposited
weld metal shall have a minimum Charpy-V-Notch impact energy
of: - correct answer - 27 J at -20°C
The minimum effective length of a fillet weld shall be ________the
size of the fillet, whichever is greater. - correct answer - mm or 4
times
CSA W47.1 AND CSA W59 EXAM 2025|
BRAND NEW ACTUAL EXAM WITH 100%
VERIFIED QUESTIONS AND CORRECT
SOLUTIONS| GUARANTEED VALUE PACK|
ACE YOUR GRADES.
When any examination indicates the presence of a planer edge
discontinuity
greater than 25 mm in depth, the_______shall refrain from any
immediate remedial work - correct answer - erector
For spot radiographic examination of welds, each spot
radiography should
show at least_________of weld length with the weld image
centered on the spot. - correct answer - 100 mm
All members and welds affected by the work shall be visually
inspected in
accordance with: - correct answer - the engineer's comprehensive
plan
, Page | 2
When application of heat is used to curve or straighten a product,
the
maximum temperature of heated areas, as measured by
approved methods, shall not exceed ________ for quenched and
tempered steels - correct answer - 590°C
When the base metal temperature is below 0°C, the base metal
shall be
preheated to at least ________and this temperature maintained
during
welding - correct answer - 10°C
For G40.21, 700QT steel 42 mm thick, the maximum preheat and
interpass
temperature shall not exceed: - correct answer - 230°C
The hole-type image quality indicator (IQI) designation, film side,
required
for ASTM A517M steel plate, 12 mm thick: - correct answer - 12
, Page | 3
Extension bars, run-off plates and backing, shall be of the same
material as the base material, for the welding of steels with a
minimum specified tensile
strength of: - correct answer - >480MPa
To establish appropriate safety and health practices and to
determine the
applicability of regulatory limitations prior to use, it is the
responsibility of: - correct answer - the user of this standard
(W59)
The filler metal for exposed bare applications of CSA 040.21-
ASTM A 242
Steel, for application to cyclically loaded structures, deposited
weld metal shall have a minimum Charpy-V-Notch impact energy
of: - correct answer - 27 J at -20°C
The minimum effective length of a fillet weld shall be ________the
size of the fillet, whichever is greater. - correct answer - mm or 4
times
