S1 Bolting Latest Update 2025-2026 Exam 55
Questions with 100% Verified Correct Answers
Guaranteed A+
A representative sample of not fewer than _____ fastener assemblies of each
combination of diameter, length, and grade of bolt used in the work shall be checked at
the site of installation to verify that the pretensioning method develops a pretension that
is equal to or greater _______ times that specified. - CORRECT ANSWER: Three ; 1.05
A tension calibrator shall be used where bolts are installed in: - CORRECT ANSWER:
Pretension joints
According to the AISC Steel Construction Manual, the grout used between the column
base plate and the foundation must be: - CORRECT ANSWER: High-strength non-
shrink
According to the AISC Steel Construction Manual, what should be done if grouting is
delayed on a base plate supported by leveling nuts until after steel erection? -
CORRECT ANSWER: Use Steel shims to support base plate
According to the AISC Steel Construction Manuel, which of the following is not an
allowed manner for setting column base plates? - CORRECT ANSWER: Treated
hardwood shims
According to the code of standard practice _____ of the steel surface is required prior to
shop painting - CORRECT ANSWER: Wire brushing
According to the code of Standard Practice for Buildings and Bridges, which party
performance material test of the structural steel for verification of material properties? -
CORRECT ANSWER: Steel supplier
, According to the code of standard practice for steel building and bridges, the ________
must be approved before the fabrication of the structural steel begins. - CORRECT
ANSWER: Shop and erection drawings
According to the code of standard practice for steel buildings and bridges ______
are(is) allowed in moderate amounts for correction of errors during steel framing
erection. - CORRECT ANSWER: • Drifts Pins
• Grinding
• Reaming
According to the code of standard practice for steel buildings and bridges ______ is the
tolerance on the length of a floor beam that is less than 30 feet long - CORRECT
ANSWER: 1/16 inch
According to the code of standard practice for steel buildings and bridges the permitted
method of applying shop paint is: - CORRECT ANSWER: • Brushing
• Rolling
• Spraying
According to the code of standard practice for steel buildings and bridges, the ______ is
responsible for the temporary vertical and lateral supports necessary for the erection of
the building framework - CORRECT ANSWER: Steel erection contractor
According to the Code of Standard Practice for Steel Buildings and Bridges, what party
is to review the fabricator's ship and erection drawings? - CORRECT ANSWER:
Owner's representatives for design and construction
According to the code of standard practice for steel buildings and bridges, what types of
openings for other trades are allowed to be cut in the structural steel - CORRECT
ANSWER: Only those openings shown on the contract document drawings and
specifications.
Questions with 100% Verified Correct Answers
Guaranteed A+
A representative sample of not fewer than _____ fastener assemblies of each
combination of diameter, length, and grade of bolt used in the work shall be checked at
the site of installation to verify that the pretensioning method develops a pretension that
is equal to or greater _______ times that specified. - CORRECT ANSWER: Three ; 1.05
A tension calibrator shall be used where bolts are installed in: - CORRECT ANSWER:
Pretension joints
According to the AISC Steel Construction Manual, the grout used between the column
base plate and the foundation must be: - CORRECT ANSWER: High-strength non-
shrink
According to the AISC Steel Construction Manual, what should be done if grouting is
delayed on a base plate supported by leveling nuts until after steel erection? -
CORRECT ANSWER: Use Steel shims to support base plate
According to the AISC Steel Construction Manuel, which of the following is not an
allowed manner for setting column base plates? - CORRECT ANSWER: Treated
hardwood shims
According to the code of standard practice _____ of the steel surface is required prior to
shop painting - CORRECT ANSWER: Wire brushing
According to the code of Standard Practice for Buildings and Bridges, which party
performance material test of the structural steel for verification of material properties? -
CORRECT ANSWER: Steel supplier
, According to the code of standard practice for steel building and bridges, the ________
must be approved before the fabrication of the structural steel begins. - CORRECT
ANSWER: Shop and erection drawings
According to the code of standard practice for steel buildings and bridges ______
are(is) allowed in moderate amounts for correction of errors during steel framing
erection. - CORRECT ANSWER: • Drifts Pins
• Grinding
• Reaming
According to the code of standard practice for steel buildings and bridges ______ is the
tolerance on the length of a floor beam that is less than 30 feet long - CORRECT
ANSWER: 1/16 inch
According to the code of standard practice for steel buildings and bridges the permitted
method of applying shop paint is: - CORRECT ANSWER: • Brushing
• Rolling
• Spraying
According to the code of standard practice for steel buildings and bridges, the ______ is
responsible for the temporary vertical and lateral supports necessary for the erection of
the building framework - CORRECT ANSWER: Steel erection contractor
According to the Code of Standard Practice for Steel Buildings and Bridges, what party
is to review the fabricator's ship and erection drawings? - CORRECT ANSWER:
Owner's representatives for design and construction
According to the code of standard practice for steel buildings and bridges, what types of
openings for other trades are allowed to be cut in the structural steel - CORRECT
ANSWER: Only those openings shown on the contract document drawings and
specifications.
