1|Page
MICHIGAN STATE BRAKES CERTIFICATION EXAM
2025| BRAND NEW ACTUAL EXAM WITH 100%
VERIFIED QUESTIONS AND CORRECT SOLUTIONS|
GUARANTEED VALUE PACK| ACE YOUR GRADES.
Most 1995 & newer vehicles use which of the following types of wheels bearings
on non-drive wheel? - (answers)Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake
pedal at least 4 times, hold the brake pedal depressed, and start the engine. the
brake pedal should: - (answers)drop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length.
Traditionally, the primary shoe lining is: - (answers)Smaller and goes towards the
front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most likely
cause: - (answers)a hard pedal feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel drive
vehicle. What is the most likely cause of this problem? - (answers)A plugged axle
Which of the following incorrect service procedures will cause brake lock-up? -
(answers)master cylinder push rod adjusted too long
, 2|Page
Which of the following describes the proper way to depressurized an ABS system?
- (answers)Pump the brake pedal at least 25 times (or more, depending on the
manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed and the drums
machined. the most likely cause is the: - (answers)technician use the parking
brake to adjust shoes and the cable is stuck
When turning brake drums: - (answers)use a dampening strap to reduce chatter
Which of the following is NOT a necessary drum brake measurement? -
(answers)run-out
On a 3-channel system, which wheels are on the same circuit? - (answers)both
rear wheels
One way to test an ABS wheel speed signal is to use _____ on your digital
multimeter. - (answers)AC volts
The key input for the ABS control module comes from the: - (answers)wheel
speed sensors
ABS speed sensor and sensor rings: - (answers)should not be hammered or
tapped on and should always be replaced as a matched set
MICHIGAN STATE BRAKES CERTIFICATION EXAM
2025| BRAND NEW ACTUAL EXAM WITH 100%
VERIFIED QUESTIONS AND CORRECT SOLUTIONS|
GUARANTEED VALUE PACK| ACE YOUR GRADES.
Most 1995 & newer vehicles use which of the following types of wheels bearings
on non-drive wheel? - (answers)Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake
pedal at least 4 times, hold the brake pedal depressed, and start the engine. the
brake pedal should: - (answers)drop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length.
Traditionally, the primary shoe lining is: - (answers)Smaller and goes towards the
front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most likely
cause: - (answers)a hard pedal feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel drive
vehicle. What is the most likely cause of this problem? - (answers)A plugged axle
Which of the following incorrect service procedures will cause brake lock-up? -
(answers)master cylinder push rod adjusted too long
, 2|Page
Which of the following describes the proper way to depressurized an ABS system?
- (answers)Pump the brake pedal at least 25 times (or more, depending on the
manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed and the drums
machined. the most likely cause is the: - (answers)technician use the parking
brake to adjust shoes and the cable is stuck
When turning brake drums: - (answers)use a dampening strap to reduce chatter
Which of the following is NOT a necessary drum brake measurement? -
(answers)run-out
On a 3-channel system, which wheels are on the same circuit? - (answers)both
rear wheels
One way to test an ABS wheel speed signal is to use _____ on your digital
multimeter. - (answers)AC volts
The key input for the ABS control module comes from the: - (answers)wheel
speed sensors
ABS speed sensor and sensor rings: - (answers)should not be hammered or
tapped on and should always be replaced as a matched set
