MASTER PLUMBER PAST BOARD EXAM
QUESTIONS SET 4 AND ANSWERS
VERIFIED TO PASS
What is the minimum dimension for a turning space in a water closet stall
intended for disabled persons?
A. 2.00 m
B. 1.20 m
C. 1.00 m
D. 1.50 m - correct answers D
Who is empowered to administer the provision of Rep. Act 1378?
A. Office of the President
B. Congress of the Philippines
C. The Board of Examiners for Master Plumbers
D. Professional Regulation Commision - correct answers C
What is the PRC Resolution Number is issued by the Board of Master
Plumbing for the adoption and promulgation of the Revised National Plumbing
Code of the Philippines?
A. Res. No. 2
B. Res. No. 1378
C. Res. No. 4
,D. Res. No. 962 - correct answers C
A kind of cleanout plugs that will be installed in case where raised heads may
cause hazards to passing personnel or vehicles.
A. depressed
B. countersunk
C. embedded
D. recessed - correct answers B
The following are grounds for non-issuance of the certificate of registration by
the Board of Master Plumbers EXCEPT
A. convicted by court for any criminal offense
B. of unsound mind
C. guilty of immoral or dishonorable conduct
D. failure to pay the required fees - correct answers D
Who shall set the criteria for the quality of drinking water from meteoric,
surface or underground sources?
A. National Water Resources Board
B. Department of Health
C. National Standards for Drinking Water
D. Department of Environment and Natural Resources - correct answers C
, If a septic tank has a compartment that exceed 3.7 m in length, what should
be the additional requirement?
A. An additional manhole
B. Increase the size of the leaching chamber
C. Increase the number of compartments
D. Baffle wall is added - correct answers A
Where the number of water closets in a floor level exceeds 20, how many of
these shall be provided to the disabled persons?
A. 1
B. 2
C. 3
D. 4 - correct answers B
What kind of concealed connections on fixtures that it is required to provide an
access panel or utility at least 0.30 meter in its least dimension for easy
inspection and repair?
A. slip joint
B. ball and socket
C. hubless
D. flanged - correct answers A
Which of the following could be omitted if the trap arm changes direction that
does not exceed 90 degrees?
QUESTIONS SET 4 AND ANSWERS
VERIFIED TO PASS
What is the minimum dimension for a turning space in a water closet stall
intended for disabled persons?
A. 2.00 m
B. 1.20 m
C. 1.00 m
D. 1.50 m - correct answers D
Who is empowered to administer the provision of Rep. Act 1378?
A. Office of the President
B. Congress of the Philippines
C. The Board of Examiners for Master Plumbers
D. Professional Regulation Commision - correct answers C
What is the PRC Resolution Number is issued by the Board of Master
Plumbing for the adoption and promulgation of the Revised National Plumbing
Code of the Philippines?
A. Res. No. 2
B. Res. No. 1378
C. Res. No. 4
,D. Res. No. 962 - correct answers C
A kind of cleanout plugs that will be installed in case where raised heads may
cause hazards to passing personnel or vehicles.
A. depressed
B. countersunk
C. embedded
D. recessed - correct answers B
The following are grounds for non-issuance of the certificate of registration by
the Board of Master Plumbers EXCEPT
A. convicted by court for any criminal offense
B. of unsound mind
C. guilty of immoral or dishonorable conduct
D. failure to pay the required fees - correct answers D
Who shall set the criteria for the quality of drinking water from meteoric,
surface or underground sources?
A. National Water Resources Board
B. Department of Health
C. National Standards for Drinking Water
D. Department of Environment and Natural Resources - correct answers C
, If a septic tank has a compartment that exceed 3.7 m in length, what should
be the additional requirement?
A. An additional manhole
B. Increase the size of the leaching chamber
C. Increase the number of compartments
D. Baffle wall is added - correct answers A
Where the number of water closets in a floor level exceeds 20, how many of
these shall be provided to the disabled persons?
A. 1
B. 2
C. 3
D. 4 - correct answers B
What kind of concealed connections on fixtures that it is required to provide an
access panel or utility at least 0.30 meter in its least dimension for easy
inspection and repair?
A. slip joint
B. ball and socket
C. hubless
D. flanged - correct answers A
Which of the following could be omitted if the trap arm changes direction that
does not exceed 90 degrees?
