Nccer Millwright Practice Exam 2 With Com o o o o o o
plete Solutions 100% 2024 o o o o
unusual
If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks
o o o o o o o o o o o o o o o o o o o
will be the indicator
o o o
sharpened brass putty knife o o o
For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended
o o o o o o o o o o o o o
Conducted on the job o o o
Apprenticeship training is_______ o o
distance
Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the in
o o o o o o o o o o o o o o o o o o o
dicator readings and into whole inches horizontally for the__________
o o o o o o o o
hidden
The orthographic drawing may contain a dashed or _______ line
o o o o o o o o o
Radiation
In order to shoot through a test object and project an image onto a detector or a sheet of film, radiography u
o o o o o o o o o o o o o o o o o o o o o
ses a source of penetrating called _______
o o o o o o
*scribe circles o
*transfer measurements o
*compare distances o
<measure angles o
Which of the following task would you not perform with dividers?
o o o o o o o o o o
10%
The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________%
o o o o o o o o o o o o o o o o
above normal full-load speed o o o
high
Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side.
o o o o o o o o o o o o o o o o
offset misalignment o
The coupling gap is set, and then the ______ is measured
o o o o o o o o o o
pressure
, In a hydraulic system, movement depends on_____
o o o o o o
furniture or utility items o o o
Fractional dimensions are used on objects such as _______ or ______
o o o o o o o o o o
elimination
If the cause of the problem is not immediately understood, the process of________is often the procedure o
o o o o o o o o o o o o o o o o
f choice
o
3/16
When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the flang
o o o o o o o o o o o o o o o o o o
e by at least_______ inch
o o o o
Transducer
A stroboscope is triggered by a_______
o o o o o
thread
The pitch of threaded fasteners is measured with a ________gauge
o o o o o o o o o
Surface cracks o
Liquid penetrant highlights flaws and reveals________
o o o o o
die
A tool used to cut external threats on s bolt or rod is called a ______
o o o o o o o o o o o o o o o
special processes o
A bill of materials may include info on _______ and other reference information
o o o o o o o o o o o o
surface speed o
Engaged gears always have the same _____o o o o o o
general arrangement o
Elevation of equipment is usually found in the_____
o o o o o o o
Vibrations
Inspect the pulleys, rollers, and idlers for unevenness or______
o o o o o o o o
15-20 degree angle o o
When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in the
o o o o o o o o o o o o o o o o o o o o
direction the torch is traveling at a _____ angle
o o o o o o o o
Grease.........
Labby seals work BEST with materials such as_____
o o o o o o o
plete Solutions 100% 2024 o o o o
unusual
If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks
o o o o o o o o o o o o o o o o o o o
will be the indicator
o o o
sharpened brass putty knife o o o
For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended
o o o o o o o o o o o o o
Conducted on the job o o o
Apprenticeship training is_______ o o
distance
Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the in
o o o o o o o o o o o o o o o o o o o
dicator readings and into whole inches horizontally for the__________
o o o o o o o o
hidden
The orthographic drawing may contain a dashed or _______ line
o o o o o o o o o
Radiation
In order to shoot through a test object and project an image onto a detector or a sheet of film, radiography u
o o o o o o o o o o o o o o o o o o o o o
ses a source of penetrating called _______
o o o o o o
*scribe circles o
*transfer measurements o
*compare distances o
<measure angles o
Which of the following task would you not perform with dividers?
o o o o o o o o o o
10%
The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________%
o o o o o o o o o o o o o o o o
above normal full-load speed o o o
high
Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side.
o o o o o o o o o o o o o o o o
offset misalignment o
The coupling gap is set, and then the ______ is measured
o o o o o o o o o o
pressure
, In a hydraulic system, movement depends on_____
o o o o o o
furniture or utility items o o o
Fractional dimensions are used on objects such as _______ or ______
o o o o o o o o o o
elimination
If the cause of the problem is not immediately understood, the process of________is often the procedure o
o o o o o o o o o o o o o o o o
f choice
o
3/16
When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the flang
o o o o o o o o o o o o o o o o o o
e by at least_______ inch
o o o o
Transducer
A stroboscope is triggered by a_______
o o o o o
thread
The pitch of threaded fasteners is measured with a ________gauge
o o o o o o o o o
Surface cracks o
Liquid penetrant highlights flaws and reveals________
o o o o o
die
A tool used to cut external threats on s bolt or rod is called a ______
o o o o o o o o o o o o o o o
special processes o
A bill of materials may include info on _______ and other reference information
o o o o o o o o o o o o
surface speed o
Engaged gears always have the same _____o o o o o o
general arrangement o
Elevation of equipment is usually found in the_____
o o o o o o o
Vibrations
Inspect the pulleys, rollers, and idlers for unevenness or______
o o o o o o o o
15-20 degree angle o o
When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in the
o o o o o o o o o o o o o o o o o o o o
direction the torch is traveling at a _____ angle
o o o o o o o o
Grease.........
Labby seals work BEST with materials such as_____
o o o o o o o
