Nccer Millwright Practice Exam 2 With Co u u u u u u
mplete Solutions 100% 2024 u u u u
unusual
If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear track
u u u u u u u u u u u u u u u u u u
s will be the indicator
u u u u
sharpened brass putty knife u u u
For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended
u u u u u u u u u u u u u
Conducted on the job u u u
Apprenticeship training is_______ u u
distance
Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the
u u u u u u u u u u u u u u u u u u
indicator readings and into whole inches horizontally for the__________
u u u u u u u u u
hidden
The orthographic drawing may contain a dashed or _______ line
u u u u u u u u u
Radiation
In order to shoot through a test object and project an image onto a detector or a sheet of film, radiograph
u u u u u u u u u u u u u u u u u u u u
y uses a source of penetrating called _______
u u u u u u u
*scribe circles u
*transfer measurements u
*compare distances u
<measure angles u
Which of the following task would you not perform with dividers?
u u u u u u u u u u
10%
The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________
u u u u u u u u u u u u u u u
% above normal full-load speed
u u u u
high
Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side.
u u u u u u u u u u u u u u u u
offset misalignment u
The coupling gap is set, and then the ______ is measured
u u u u u u u u u u
pressure
, In a hydraulic system, movement depends on_____
u u u u u u
furniture or utility items u u u
Fractional dimensions are used on objects such as _______ or ______
u u u u u u u u u u
elimination
If the cause of the problem is not immediately understood, the process of________is often the procedure
u u u u u u u u u u u u u u u u
of choice
u
3/16
When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the fla
u u u u u u u u u u u u u u u u u u
nge by at least_______ inch
u u u u
Transducer
A stroboscope is triggered by a_______
u u u u u
thread
The pitch of threaded fasteners is measured with a ________gauge
u u u u u u u u u
Surface cracks u
Liquid penetrant highlights flaws and reveals________
u u u u u
die
A tool used to cut external threats on s bolt or rod is called a ______
u u u u u u u u u u u u u u u
special processes u
A bill of materials may include info on _______ and other reference information
u u u u u u u u u u u u
surface speed u
Engaged gears always have the same _____
u u u u u u
general arrangement u
Elevation of equipment is usually found in the_____
u u u u u u u
Vibrations
Inspect the pulleys, rollers, and idlers for unevenness or______
u u u u u u u u
15-20 degree angle
u u
When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in th
u u u u u u u u u u u u u u u u u u u
e direction the torch is traveling at a _____ angle
u u u u u u u u u
Grease.........
Labby seals work BEST with materials such as_____
u u u u u u u
mplete Solutions 100% 2024 u u u u
unusual
If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear track
u u u u u u u u u u u u u u u u u u
s will be the indicator
u u u u
sharpened brass putty knife u u u
For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended
u u u u u u u u u u u u u
Conducted on the job u u u
Apprenticeship training is_______ u u
distance
Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the
u u u u u u u u u u u u u u u u u u
indicator readings and into whole inches horizontally for the__________
u u u u u u u u u
hidden
The orthographic drawing may contain a dashed or _______ line
u u u u u u u u u
Radiation
In order to shoot through a test object and project an image onto a detector or a sheet of film, radiograph
u u u u u u u u u u u u u u u u u u u u
y uses a source of penetrating called _______
u u u u u u u
*scribe circles u
*transfer measurements u
*compare distances u
<measure angles u
Which of the following task would you not perform with dividers?
u u u u u u u u u u
10%
The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________
u u u u u u u u u u u u u u u
% above normal full-load speed
u u u u
high
Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side.
u u u u u u u u u u u u u u u u
offset misalignment u
The coupling gap is set, and then the ______ is measured
u u u u u u u u u u
pressure
, In a hydraulic system, movement depends on_____
u u u u u u
furniture or utility items u u u
Fractional dimensions are used on objects such as _______ or ______
u u u u u u u u u u
elimination
If the cause of the problem is not immediately understood, the process of________is often the procedure
u u u u u u u u u u u u u u u u
of choice
u
3/16
When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the fla
u u u u u u u u u u u u u u u u u u
nge by at least_______ inch
u u u u
Transducer
A stroboscope is triggered by a_______
u u u u u
thread
The pitch of threaded fasteners is measured with a ________gauge
u u u u u u u u u
Surface cracks u
Liquid penetrant highlights flaws and reveals________
u u u u u
die
A tool used to cut external threats on s bolt or rod is called a ______
u u u u u u u u u u u u u u u
special processes u
A bill of materials may include info on _______ and other reference information
u u u u u u u u u u u u
surface speed u
Engaged gears always have the same _____
u u u u u u
general arrangement u
Elevation of equipment is usually found in the_____
u u u u u u u
Vibrations
Inspect the pulleys, rollers, and idlers for unevenness or______
u u u u u u u u
15-20 degree angle
u u
When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in th
u u u u u u u u u u u u u u u u u u u
e direction the torch is traveling at a _____ angle
u u u u u u u u u
Grease.........
Labby seals work BEST with materials such as_____
u u u u u u u
