m m m m m m
100% Correct | Grade A+ m m m m
1. In general, mold modifications are as follows
m m m m m m
Answer Venting affects lows, damping the midrange and horn effects boost highs.
m m m m m m m m m m m
2. Basic verification involves
m m
Answer checking MCL and UCL in quiet and noise.
m m m m m m m m
3. Sound field ism m
Answer a controlled environment
m m m
4. The configuration and height of the tympanogram can be a factor in decid-
m m m m m m m m m m m m
ing the proper matrix for the fitting of a hearing aid
m m m m m m m m m m m
Answer A high Type A tells us to decrease the output by 2-3 dB
m m m m m m m m m m m m m
5. You cannot use feedback checks when
m m m m m
Answer checking the telephone coil
m m m m
1m/m41
,6. Verification procedures m
Answer Check the accuracy of your fitting.
m m m m m m
7. The problems produced by excessive ambient noise are
m m m m m m m
Answer greater for the lower frequencies than the higher frequencies
m m m m m m m m m
8. The decibel is
m m
Answer a ratio between two intensities
m m m m m
9. REUR measurement are taken in
m m m m
Answer an open human ear canal
m m m m m
10. When a hearing aid is dead, you can check the receiver and microphone
m m m m m m m m m m m m
function by
m m
Answer turning on the instrument telecoil
m m m m m
11. The dividing line between the external and middle ear is the
m m m m m m m m m m
Answer tympanic membrane
m m
12. The cochlea, acting as a frequency analyzer, distributes acoustic stimuli
m m m m m m m m m m
to places along the basilar membrane according to frequency. This forms the
m m m m m m m m m m m
basis of a hypothesis called the
m m m m m m
Answer Place Theory
m m
13. An organic disorder is when there is damage to
m m m m m m m m
Answer The hearing mechanism, the neural pathways and the brain.
m m m m m m m m m
2m/m41
,14. The speed of sound in air, in feet per second, is
m m m m m m m m m m m
Answer 1100 m
15. Properly selected hearing instruments should allow
m m m m m
Answer The patient to wear an instrument at a comfortable loudness level, improv
m m m m m m m m m m m m
ed communication and have better hearing aided.
m m m m m m
16. Crystal microphones and receivers
m m m
Answer are very fragile
m m m
17. Which of the following is not a coupler used for measuring hearing aid
m m m m m m m m m m m m
performance?
m
Answer Zwisks Ear Simulator
m m m
18. Small diameter tubing of SIA hearing aids has the effect of
m m m m m m m m m m m
Answer reducing the high frequency gain
m m m m m
19. The function of a microphone is to
m m m m m m m
Answer convert acoustic energy into electrical energy
m m m m m m
20. Vent an earmold
m m m
Answer is the most common modification made on an earmold
m m m m m m m m m
21. When a new hearing instrument has feedback at the patients comfortable
m m m m m m m m m m
level, the problem is usually
m m m m m
Answer too much wax in the ear canal
m m m m m m m
3m/m41
, 22. With SIE-S hearing aids
m m m
Answer The only signal is from the hearing aid and phrase effects from a vent are
m m m m m m m m m m m m m m m
m not an issue.
m m
23. The most comfortable level is
m m m m
Answer About 45 dB HL or 65 dB SPL for normal ears
m m m m m m m m m m m
24. Any complex sound can be broken down into individual frequencies by a
m m m m m m m m m m m
m technique known as m m
Answer Fourier Spectral analysis
m m m
25. The adult ear canal
m m m
Answer rises upward and forward, then descends to the drum.
m m m m m m m m m
26. An effective verification is
m m m
Answer a measure able improvement in communication
m m m m m m
27. Which of the following is not included in correct test protocols?
m m m m m m m m m m
Answer plugging the hearing aid vent to control feedback
m m m m m m m m
28. Most conducive losses m m
Answer Are medically correctable, display a breakdown or obstruction in middle
m m m m m m m m m m m
ear and display good discrimination
m m m m
29. The T position on a hearing aid switch can be used to
m m m m m m m m m m m
Answer amplify a telephone conversation, couple hearing aid into a loop inductor,
m m m m m m m m m m m m
4m/m41