025/2026 UPDATED MSSC TEST EXAM
2
WITH Q&A 100% GUARANTEED
hich is NOT one of the steps used in the glass box method?
W
rotate object in glass box
The three standard views of an object are ______.
top, front, right side
What is the order of precedence of lines in a drawing?
object, hidden, center
What type of feature is parallel to the surface being dimensioned?
dimension line
A ______ dimension is described in inches per foot.
shaft taper
To establish on a drawing that 1/4 inch equals 1 inch, the designer would write ______.
1/4 = 1
Section lines on a blueprint include _______.
a surface that has been cut
In a threaded fastener assembly what is designed to protect the threads?
shank
The minor diameter of a screw thread is measured at the ______.
root of screw thread
The minor diameter of a threaded fastener is ______.
the major diameter minus the thread height
How do you determine the grade of a bolt?
number of lines on the head +2 indicates the grade
A screw with National fine thread is represented on a drawing with what designation?
NF
Metals treated by ______ processes become soft.
annealing
A running fit is also called a(n) ______.
sliding fit
The term ______ refers to a physical portion of a part.
feature
A(n) _______ is a theoretically perfect line, point or pane that is located by a similar
feature or part.
datum
GD&T _________________.
, llows certain tolerances on part features to be increased
a
A feature control frame is not used to describe ______.
measurements
A common decimal inch rule graduation is in _______.
50ths
A scale typically found on a machinist rule is _______.
1/16
Resolution is sometimes called ______.
discrimination
A common fractional inch rule graduation is in _______.
32nds
One inch is equal to _______.
25.4mm
A typical dial caliper can be used to measure dimensions to the nearest ________
inches.
0.001
Calibration means to ______.
adjust a device to a standard
The typical accuracy of a dial caliper is about ______ inches.
0.003
The accuracy of a digital caliper reading is about ______ inches.
0.003
A micrometer increments how far for each complete rotation of its thimble?
0.025
Company standards determine how often ______ is performed.
calibration of surface finish gaues
The dial indicator makes measurements using the ______ method.
indirect comparison
The best method for checking the height of two or more parts is to use a dial indicator
and stand, gauge block and a ______.
surface plate
A _______ is a measurement tool that measures part dimensions by indicating the
amount of distance its probe moves when placed against the part.
dial indicator
_______ measures the difference between an object's dimension and an object of
known length.
indirect comparison
The process of zeroing the probe using a part that has been found to be a precise
length is known as ______.
mastering
2
WITH Q&A 100% GUARANTEED
hich is NOT one of the steps used in the glass box method?
W
rotate object in glass box
The three standard views of an object are ______.
top, front, right side
What is the order of precedence of lines in a drawing?
object, hidden, center
What type of feature is parallel to the surface being dimensioned?
dimension line
A ______ dimension is described in inches per foot.
shaft taper
To establish on a drawing that 1/4 inch equals 1 inch, the designer would write ______.
1/4 = 1
Section lines on a blueprint include _______.
a surface that has been cut
In a threaded fastener assembly what is designed to protect the threads?
shank
The minor diameter of a screw thread is measured at the ______.
root of screw thread
The minor diameter of a threaded fastener is ______.
the major diameter minus the thread height
How do you determine the grade of a bolt?
number of lines on the head +2 indicates the grade
A screw with National fine thread is represented on a drawing with what designation?
NF
Metals treated by ______ processes become soft.
annealing
A running fit is also called a(n) ______.
sliding fit
The term ______ refers to a physical portion of a part.
feature
A(n) _______ is a theoretically perfect line, point or pane that is located by a similar
feature or part.
datum
GD&T _________________.
, llows certain tolerances on part features to be increased
a
A feature control frame is not used to describe ______.
measurements
A common decimal inch rule graduation is in _______.
50ths
A scale typically found on a machinist rule is _______.
1/16
Resolution is sometimes called ______.
discrimination
A common fractional inch rule graduation is in _______.
32nds
One inch is equal to _______.
25.4mm
A typical dial caliper can be used to measure dimensions to the nearest ________
inches.
0.001
Calibration means to ______.
adjust a device to a standard
The typical accuracy of a dial caliper is about ______ inches.
0.003
The accuracy of a digital caliper reading is about ______ inches.
0.003
A micrometer increments how far for each complete rotation of its thimble?
0.025
Company standards determine how often ______ is performed.
calibration of surface finish gaues
The dial indicator makes measurements using the ______ method.
indirect comparison
The best method for checking the height of two or more parts is to use a dial indicator
and stand, gauge block and a ______.
surface plate
A _______ is a measurement tool that measures part dimensions by indicating the
amount of distance its probe moves when placed against the part.
dial indicator
_______ measures the difference between an object's dimension and an object of
known length.
indirect comparison
The process of zeroing the probe using a part that has been found to be a precise
length is known as ______.
mastering
