CSWA-S Multiple Choice Q- Extended Edition With Correct
Answers
1. 1. What is the Modulus of Elasticity?
B. The slope of the
A. The slope of the Deflection-Stress curve.
Stress-Strain curve in
B. The slope of the Stress-Strain curve in its
its linear section.
linear section.
C. The slope of the Force-Deflection curve in its
linear section.
D. The first inflection point of a Strain curve.
2. 2. What is Stress? D. A measure of the
A. A measure of power. aver- age amount of
B. A measure of strain. force exert- ed per unit
C. A measure of material strength. area.
D. A measure of the average amount of force
exerted per unit area.
3. 3. Which of the following assumptions are true
for a static analysis in SOLIDWORKS Simulation A,C, D
with small displacements? A. Inertia ettects are
A. Inertia effects are negligible and loads are neg- ligible and loads
applied slowly. are ap- plied slowly.
B. The model is not fully elastic. If loads are C. Results are
removed, the model will not return to its proportional to loads.
original position. D. All the
C. Results are proportional to loads. displacements are
small relative to the
D.All the displacements are small relative to the mod- model
geometry.
el geometry.
4. 4. What is Yield Stress? A. The stress level be-
A.The stress level beyond which the material becomes yond which
the material
, CSWA-S Multiple Choice Q- Extended Edition With Correct
Answers
plastic. becomes plastic.
B. The stress level beyond which the material
breaks.
C. Results are proportional to loads.
, CSWA-S Multiple Choice Q- Extended Edition With Correct
Answers
D.All the displacements are small relative to
the mod- el geometry.
5. 5. A high quality Shell element has nodes. C. 6
A. 4
B. 5
C. 6
D. 8
6. 6. Stress is proportional to in a Linear Elastic Mate- A. Strain.
rial.
A. Strain.
B. Stress.
C. Force.
D. Pressure.
7. 7. The Elastic Modulus (Young's Modulus) is B. Stress, Strain.
the slope defined as divided by .
A. Strain, Stress.
B. Stress, Strain.
C. Stress, Force.
D. Force, Area.
8. 8. Linear static analysis assumes that the relationship B. Linear.
between loads and the induced response is .
A. Flat.
B. Linear.
C. Doubles per area.
D. Translational.
9. 9. In SOLIDWORKS Simulation, the Factor of the
Safety (FOS) calculations are based on one of following
, CSWA-S Multiple Choice Q- Extended Edition With Correct
Answers
All- A, B, C, and D.
A. Maximum von Mises
Answers
1. 1. What is the Modulus of Elasticity?
B. The slope of the
A. The slope of the Deflection-Stress curve.
Stress-Strain curve in
B. The slope of the Stress-Strain curve in its
its linear section.
linear section.
C. The slope of the Force-Deflection curve in its
linear section.
D. The first inflection point of a Strain curve.
2. 2. What is Stress? D. A measure of the
A. A measure of power. aver- age amount of
B. A measure of strain. force exert- ed per unit
C. A measure of material strength. area.
D. A measure of the average amount of force
exerted per unit area.
3. 3. Which of the following assumptions are true
for a static analysis in SOLIDWORKS Simulation A,C, D
with small displacements? A. Inertia ettects are
A. Inertia effects are negligible and loads are neg- ligible and loads
applied slowly. are ap- plied slowly.
B. The model is not fully elastic. If loads are C. Results are
removed, the model will not return to its proportional to loads.
original position. D. All the
C. Results are proportional to loads. displacements are
small relative to the
D.All the displacements are small relative to the mod- model
geometry.
el geometry.
4. 4. What is Yield Stress? A. The stress level be-
A.The stress level beyond which the material becomes yond which
the material
, CSWA-S Multiple Choice Q- Extended Edition With Correct
Answers
plastic. becomes plastic.
B. The stress level beyond which the material
breaks.
C. Results are proportional to loads.
, CSWA-S Multiple Choice Q- Extended Edition With Correct
Answers
D.All the displacements are small relative to
the mod- el geometry.
5. 5. A high quality Shell element has nodes. C. 6
A. 4
B. 5
C. 6
D. 8
6. 6. Stress is proportional to in a Linear Elastic Mate- A. Strain.
rial.
A. Strain.
B. Stress.
C. Force.
D. Pressure.
7. 7. The Elastic Modulus (Young's Modulus) is B. Stress, Strain.
the slope defined as divided by .
A. Strain, Stress.
B. Stress, Strain.
C. Stress, Force.
D. Force, Area.
8. 8. Linear static analysis assumes that the relationship B. Linear.
between loads and the induced response is .
A. Flat.
B. Linear.
C. Doubles per area.
D. Translational.
9. 9. In SOLIDWORKS Simulation, the Factor of the
Safety (FOS) calculations are based on one of following
, CSWA-S Multiple Choice Q- Extended Edition With Correct
Answers
All- A, B, C, and D.
A. Maximum von Mises
