Page |1
NEIEP 200 FINAL EXAM (COURSES 205-250)
2025| BRAND NEW ACTUAL EXAM WITH 100%
VERIFIED QUESTIONS AND CORRECT
SOLUTIONS| GUARANTEED VALUE PACK| ACE
YOUR GRADES.
You are preparing to unload a truck at the loading dock and the truck is 8"
higher than the dock. What do you do? - Correct Answer-use a steel plate
to span the gap
You just finished the surface inspection of a manila rope you will be using
for hoisting. What method should you use to conduct an internal
inspection? - Correct Answer-slightly untwist the strands
You are preparing to hoist rails and are inspecting your manila rope. Which
of the following is a good characteristic of manila rope? - Correct Answer-a
light yellow color with a silvery or pearly luster
A mechanic attaches a chainfall to a hoisting beam with a beam clamp.
What happens to the capacity of the hoisting beam? - Correct Answer-it is
reduced to 50% of original capacity
You are rigging elevator equipment with a sling angle of 60 degrees. You
are using a shouldered eye bolt with a tapped 1/2" diameter hole. Once the
, Page |2
shoulder is seated, what is the minimum thread depth required? - Correct
Answer-at least 3/4"
You are about to loosen a fishplate bolt. Which wrench would be least likely
to slip? - Correct Answer-a. 6 point box end wrench
B. 12 point box end wrench
C. Open end wrench
You are using a plumb line to check a rail for plumb. You find that at the top
it measures 1" and at the bottom it measures 1 1/4". What does this tell
you? - Correct Answer-a. The top of the rail needs to go towards the center
B. The top of the rail needs to go toward the wall
C. The bottom of the rail needs to go toward the wall
You are plumbing rails on a high rise installation. What type of plumb line
should you use? - Correct Answer-a. Nylon string
B. Monofilament wire
C. Piano wire
You need to cut into a concrete wall. Which tool should you use? - Correct
Answer-disc grinder with a diamond blade disc
You need to select a heavy duty drill for drilling 5/8" holes in a machine
beam. What factor determines the drill rating? - Correct Answer-chuck size
, Page |3
You are tasked with setting 3/4" concrete anchors. Which type of drill
should you use? - Correct Answer-rotary hammer
You need to cut and 8ft section of 1/2" EMT conduit pipe. What would be
the best tool for the job? - Correct Answer-hacksaw with 24 teeth per inch
You are directed to move oxy-acetylene cylinders from a storage area to a
work site. What is the proper way to transport them? - Correct Answer-in an
upright position
You are setting up welding equipment. What is the maximum psi that the
regulator for the acetylene gas may be adjusted to? - Correct Answer-10-
12 psi
You are using rollers to move a heavy elevator machine and are
approaching a corner. Which technique should you use to maneuver
around it? - Correct Answer-angle front roller gradually and continue
around the corner
NEIEP 200 FINAL EXAM (COURSES 205-250)
2025| BRAND NEW ACTUAL EXAM WITH 100%
VERIFIED QUESTIONS AND CORRECT
SOLUTIONS| GUARANTEED VALUE PACK| ACE
YOUR GRADES.
You are preparing to unload a truck at the loading dock and the truck is 8"
higher than the dock. What do you do? - Correct Answer-use a steel plate
to span the gap
You just finished the surface inspection of a manila rope you will be using
for hoisting. What method should you use to conduct an internal
inspection? - Correct Answer-slightly untwist the strands
You are preparing to hoist rails and are inspecting your manila rope. Which
of the following is a good characteristic of manila rope? - Correct Answer-a
light yellow color with a silvery or pearly luster
A mechanic attaches a chainfall to a hoisting beam with a beam clamp.
What happens to the capacity of the hoisting beam? - Correct Answer-it is
reduced to 50% of original capacity
You are rigging elevator equipment with a sling angle of 60 degrees. You
are using a shouldered eye bolt with a tapped 1/2" diameter hole. Once the
, Page |2
shoulder is seated, what is the minimum thread depth required? - Correct
Answer-at least 3/4"
You are about to loosen a fishplate bolt. Which wrench would be least likely
to slip? - Correct Answer-a. 6 point box end wrench
B. 12 point box end wrench
C. Open end wrench
You are using a plumb line to check a rail for plumb. You find that at the top
it measures 1" and at the bottom it measures 1 1/4". What does this tell
you? - Correct Answer-a. The top of the rail needs to go towards the center
B. The top of the rail needs to go toward the wall
C. The bottom of the rail needs to go toward the wall
You are plumbing rails on a high rise installation. What type of plumb line
should you use? - Correct Answer-a. Nylon string
B. Monofilament wire
C. Piano wire
You need to cut into a concrete wall. Which tool should you use? - Correct
Answer-disc grinder with a diamond blade disc
You need to select a heavy duty drill for drilling 5/8" holes in a machine
beam. What factor determines the drill rating? - Correct Answer-chuck size
, Page |3
You are tasked with setting 3/4" concrete anchors. Which type of drill
should you use? - Correct Answer-rotary hammer
You need to cut and 8ft section of 1/2" EMT conduit pipe. What would be
the best tool for the job? - Correct Answer-hacksaw with 24 teeth per inch
You are directed to move oxy-acetylene cylinders from a storage area to a
work site. What is the proper way to transport them? - Correct Answer-in an
upright position
You are setting up welding equipment. What is the maximum psi that the
regulator for the acetylene gas may be adjusted to? - Correct Answer-10-
12 psi
You are using rollers to move a heavy elevator machine and are
approaching a corner. Which technique should you use to maneuver
around it? - Correct Answer-angle front roller gradually and continue
around the corner
